Collection: Boating Supplies

■Material: Stainless steel (SUS316)
■Size
Total length 152 x stop hole ~ stop hole 57 x height 31mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

■Material: Stainless steel (SUS316)
■Size
Total length 203 x stop hole ~ stop hole 73 x height 38 mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

■Material: Stainless steel (SUS316)
■Size
Total length 203 x stop hole ~ stop hole 84 x height 51 mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

■Material: Stainless steel (SUS316)
■Size
Total length 308 x stop hole ~ stop hole 122 x height 68 mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

[Product specifications]
■Material: Stainless steel (SUS304)
■Size:
Total length: 260mm
Pedestal dimensions: 85x57mm
■Holder inner diameter
⇒With rubber: 40mm
⇒No rubber: 48mm
[Contents] 5-piece set: rod holder, rubber, stop bolt, intermediate pedestal, and pedestal.

A rod holder that rotates 360° and allows you to freely set the vertical angle according to your preference.
Rubber is pasted on the inside of the rod holder, so there is no need to worry about damaging the rod.

[Product specifications]
■Material (float): PVC foam
■Float body (per piece)
Size: 141φ×175mm
Hole diameter: 25φ
...

■Rope
Size: 12φ×2m

[Float x 3] + [Rope]
●This is a fender that uses egg-shaped vinyl chloride foam in three rows.
●Float body material: PVC foam

[Contents] 2L
[How to use] For removing red rust, blue rust on the hull, removing stains from the wood of the deck, and cleaning light oily substances.

It does not cause corrosion damage to painted surfaces or metal surfaces of the hull, and the luster of the hull does not disappear.

▼How to use▼
Wet the area to be cleaned with water before use.
For normal use, dilute it 3 times and adjust the concentration depending on the degree of dirt.
Using rubber gloves, thoroughly soak a brush, sponge, or cloth in detergent and scrub depending on the degree of dirt.
Be sure to rinse thoroughly with plenty of tap water within 2 minutes to ensure that no Hytrail ingredients remain.
Wipe off moisture with a dry cloth.

*Please try it in an inconspicuous place before use.
*Do not leave it on for more than 2 minutes as it may change color.

Notes
・Never use a spray bottle.
・Do not use on glass surfaces such as automobiles or aluminum parts of vehicles.
・Please do not use the product under the blazing sun or when the product is hot, as stains and uneven color may occur and will be difficult to wipe off.
・Please do not use coatings (mirror finishing, etc.) or painted areas as they will peel off.

CASTRO
Castro Fender was born in Spain in the early 1970s by founder Carlos Castro.
Castro is now one of the world's largest manufacturers of buoy fender floats.
Our products are sold in over 70 countries around the world and are widely praised for their outstanding quality and innovative design.

■Size: Diameter/Total length/Eye diameter
A-0HD: 200mm / 270mm / 25mm
A-1HD: 290mm / 370mm / 25mm

●It is a drop-shaped air fender.
●The rope attachment hole is thick and reinforced with ribs, making it extremely durable. ,
●Can also be used as a course buoy if installed upside down.
●You can easily inflate with an air compressor or air gun.

【please note】
*Air injection nozzle not included *Delivered with air removed *As this is an overseas product, specifications may change without notice.

[Product specifications]
■Material: Nylon ■Rope diameter: 1/2 (12.7mm)
■Length: 200ft (60m), 300ft (90m)

An easy-to-handle nylon triple rope with excellent abrasion resistance, strength, and flexibility.

A coating agent containing fluorine-modified silicone.
For protecting and polishing gel coat surfaces of boats and PWCs!
For reproducing black color and polishing resin moldings and gunwales!

■Construction guideline
Aerosol 420ml, application area: approximately 3 to 5.24 feet 2 bottles for ships, 1 bottle for PWC
■Construction method
1. Remove dirt and debris from the area to be applied with a cleaning agent and dry.
2.Apply Marine Glass Coat and spread it over the entire surface using a cloth such as a microfiber cloth.
3. Let it dry at room temperature for about 3 to 8 hours.

●Marine Glass Coat is a coating agent for ship hulls that contains fluorine-modified silicone.
●By forming a glass-like film on the gel coat or painted surface, it creates a glossy luster, and
The water repellent effect reduces the adhesion of dirt and rust, making subsequent cleaning easier◎
●It cures easily at room temperature, so you can easily apply the coating yourself.
It can be used for FRP, so it can be used not only for boat hulls but also for camper shells etc.

[Product specifications]
●Voltage: 12V
●Current: 3.4A
-External dimensions: 74 x 64 x height 111mm (dimensions in image)
●Drainage volume 50 liters/min
●Compatible with hose diameter 19.0mm
[Adaptation] Ideal for PWC (personal watercraft) and small boats

●Since it is a completely waterproof submersible pump, it is a convenient product for circulating and draining water while on board or during maintenance.
●When wiring, insert a 7.5A fuse (*) on the + cord side.
(*Fuse is not included with this product and must be purchased separately)

[Product specifications]
●Voltage: 12V
●Current: 1.6A
-External dimensions: 74 x 64 x height 99mm (dimensions in image)
●Displacement volume 31 liters/min
●Compatible with hose diameter 19.0mm
[Adaptation] Ideal for PWC (personal watercraft) and small boats

●Since it is a completely waterproof submersible pump, it is a convenient product for circulating and draining water while on board or during maintenance.
●When wiring, insert a 4A fuse (*) on the + cord side.
(*Fuse is not included with this product and must be purchased separately)

●Type approval number No. 745
-Can be installed on flat water vessels
●Surface is polyester vinyl chloride waterproof cloth (flame retardant)
●The buoyant body is made of closed polyethylene foam. Normally you can put it on a cushion, but in an emergency, grab it with both hands and jump in.
■Buoyancy: 9.3kg
■Size: 400×400×60mm

[Product Specifications]
■Ideal for carrying spare fuel! Since it is a plastic tank, there is no need to worry about rust, and it is lightweight and easy to carry.

■The included nozzle has an air intake vent, allowing you to pour fuel smoothly.

■Size: Approx. 265 x 250 x 135 mm
■Aperture: Φ40mm
■Material: HDPE (high density polyethylene)
Capacity: 5 liters

*The product is a hazardous materials transport container that complies with international recommendations (UN standards) regarding the international transportation of hazardous materials.
*Although this product is UN certified, it may not be possible to fill it up at gas stations, including self-service stations.
*This product cannot be refueled and transported in a passenger vehicle for the purpose of using it as automobile fuel. (*1)
*This product cannot be used for refueling for storage purposes (*2).

(*1) Notification prescribing details of technical standards for the control of dangerous goods (Article 68-4), Regulations on the Control of Hazardous Materials (Article 43-2)
(*2) Fueling for storage purposes refers to fueling for stockpiling. This does not apply if the purpose is to use it immediately. There is no clear definition of the time between refueling and use.

●It is sized to fit a 500ml plastic bottle.
●Since it is easy to install and remove, it is perfect for cases where the base cannot be fixed with screws, such as cooler boxes or shared boats.

Inner diameter: approx. 71mm
Material: resin
-Includes 2 screws for insert parts

sucker base
Size: Height 75 x Width 70 x Depth 60mm
Material: resin
Weight: 60g
Load capacity: 6kg (according to manufacturer)
*Depending on the object to be installed and the usage environment, it may not be possible to adsorb it sufficiently.
*The load value is the hanging load capacity value on a smooth acrylic board. (according to manufacturer research)
This is not the load value including vibration and impact.

●You can hang garbage bags, pliers, etc.
●Since it is easy to install and remove, it is perfect for cases where the base cannot be fixed with screws, such as cooler boxes or shared boats.

Size: Height 46 x Width 28 x Depth 48mm
Material: resin
Hook load capacity: 5kg (according to manufacturer)

sucker base
Size: Height 75 x Width 70 x Depth 60mm
Material: resin
Weight: 60g
Load capacity: 6kg (according to manufacturer)
*Depending on the object to be installed and the usage environment, it may not be possible to adsorb it sufficiently.
*The load value is the hanging load capacity value on a smooth acrylic board. (according to manufacturer research)
This is not the load value including vibration and impact.

●The height of the holder can be adjusted according to the rod.
●There is a notch on the back for triggering the bait reel.
●Since it is easy to install and remove, it is perfect for cases where the base cannot be fixed with screws, such as cooler boxes or shared boats.

Size: Approximately L240 x Φ40mm *Protrusions are not included.
Inner diameter: 35mm
Outer diameter: 40mm
Material: resin

sucker base
Size: Height 75 x Width 70 x Depth 60mm (lever up) / Depth 29mm (lever down)
Material: resin
Weight: 60g
Load capacity: 6kg (according to manufacturer)
*Depending on the object to be installed and the usage environment, it may not be possible to adsorb it sufficiently.
*The load value is the hanging load capacity value on a smooth acrylic board. (according to manufacturer research)
This is not the load value including vibration and impact.

●The height of the holder can be adjusted according to the rod.
●There is a notch on the back for triggering the bait reel.
●Since it is easy to install and remove, it is perfect for cases where the base cannot be fixed with screws, such as cooler boxes or shared boats.

Size: Approximately L305 x Φ50mm *Protrusions are not included.
Inner diameter: 45mm
Outer diameter: 50mm
Material: resin

sucker base
Size: Height 75 x Width 70 x Depth 60mm (lever up) / Depth 29mm (lever down)
Material: resin
Weight: 60g
Load capacity: 6kg (according to manufacturer)
*Depending on the object to be installed and the usage environment, it may not be possible to adsorb it sufficiently.
*The load value is the hanging load capacity value on a smooth acrylic board. (according to manufacturer research)
This is not the load value including vibration and impact.

■Material: Stainless steel

■Size: A total length 304 x B stop hole ~ stop hole 100 x C height 70 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

■Material: Stainless steel

■Size: A total length 254 x B stop hole ~ stop hole 93 x C height 68 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

■Material: Stainless steel

■Size: A total length 203 x B stop hole ~ stop hole 71 x C height 53 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

■Material: Stainless steel

■Size: A total length 152 x B stop hole ~ stop hole 75 x C height 45 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

■Material: Stainless steel

■Size: A total length 126 x B stop hole ~ stop hole 54 x C height 39 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

●A stainless steel bracket for fixing navigation lights to pipes, etc.
●You can adjust the angle and install it horizontally even on a sloped wall.

●Bracket for Ibuki Kogyo navigation light “NAUTILIGHT NAVI”
●Adaptation: For 25φ pipe
●Material: Stainless steel SUS316 (main body), SUS304 (attached metal fittings)

【please note】
*Only the bracket is included, and the screws and rubber gaskets that secure the main body and navigation light are not included.

●Stainless steel bracket for fixing navigation lights to pipes, etc.

●Bracket for Ibuki Kogyo's navigation light "NAUTILIGHT NAVI"
●For diameter 25φ pipe
●Material: Stainless steel SUS316 (main body), SUS304 (attached metal fittings)

【please note】
*Only the bracket is included, and the screws and rubber gaskets that secure the main body and navigation light are not included.

●Stainless steel bracket for fixing navigation lights to pipes, etc.

●Bracket for Ibuki Kogyo's navigation light "NAUTILIGHT NAVI"
●Mounting part diameter: 68mm
●For diameter 25φ pipe
●Material: Stainless steel SUS316 (main body), SUS304 (attached metal fittings)

【please note】
*Bracket only; screws and rubber gaskets to secure the main body and navigation light are not included.

●This cylinder set is a replacement cylinder set for the gas cylinder of BJ-270/BJ-2700 inflatable life jackets.

● Replacement cylinder spool set

【 correspondence 】
● Toyo Bussan Inflatable Life Jacket BJ-270 Waist Belt Type

● Toyo Bussan Inflatable Life Jacket BJ-2700 Neck type

●This is a light that is attached to the bow part of a ship. *For ships with a total length of less than 12m

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLB-5AB2

●Type approval number No. 5300

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Advanced technology condensed into a small body!

●Machine-cut heat dissipation plate: A beautiful heat dissipation plate machine-cut from high-strength aluminum and specially treated to efficiently dissipate the heat generated by the LED, achieving an LED unit life of approximately 60,000 hours.

●High light-shielding performance: Based on our unique theory, all parts are placed with high precision to achieve complete light-shielding.

●Wide power supply voltage compatible: The LED unit supports a wide power supply of DC10 to 30V. Built-in stabilization circuit completely absorbs voltage fluctuations.

●Excellent weather resistance and impact resistance: The housing is made of polycarbonate resin. The metal parts are also made of highly weather-resistant materials to ensure high durability and reliability.

●Replaceable LED unit: By replacing the unit at the specified LED time (approximately 60,000 hours), maximum performance can always be achieved.

●Low power consumption: We have succeeded in significantly reducing power consumption by switching to LED. Cut power consumption by up to 90%.

●Installation compatibility: Compatible with conventional Koito products at the same pitch and can be easily replaced.

●GOOD Design GOOD Quality: Winner of the 2013 Good Design Award. made in Japan.

●The size is Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50), the weight is 0.2kg, and the mounting pitch is the same as the old standard Koito Seisakusho type.

*The special packing (product number: 35269) sold separately is a vibration-proof rubber packing that is installed between the boat light and the installation pedestal, etc., and is recommended to be installed to prevent damage to the main unit. The main body has a waterproof structure.

【 specification 】
Manufacturer: Ibuki Kogyo Co., Ltd.
Model: NLST-2Y
Light source: LED
Power supply voltage: DC10V to 30V
Power consumption: 3W
LED unit life: about 60000 hours
Protection grade: IP56
Dimensions: Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50, same as conventional Koito products)
Weight: 0.2kg

[Product specifications]
●12V power can be easily extracted from the cigarette lighter socket and terminal.

●Compatible with taking out electric power! This is a new type of battery BOX whose main terminal has a 60A circuit breaker.

●In accordance with modern needs, it is also equipped with a USB charger socket.

●Equipped with a battery level gauge, so you can conveniently check the remaining battery level with the touch of a button without having to open the lid.

●Socket type: Cigarette lighter (1 burner), USB (2 burners)
●USB socket specifications: Output voltage (DC5V)/Output current (2.1A)
●Built-in breaker: 10A (cigar socket)/60A (main terminal)
●Breaker type: manual reset
●Compatible battery: For 105A or less
-External dimensions: W420 x D230 x H335mm
-Inner dimensions: W340 x D190 x H225mm
(There is a protrusion on the back of the lid to hold the battery in place.)

*If more than the specified current flows, the breaker will operate and shut down the current.
After tripping the breaker, wait a sufficient amount of time before pressing the reset button.

●Press the start switch for 2 to 4 seconds to automatically start suction and drainage, and when drainage is complete, the motor will automatically stop, so there is no need to worry about dry running.

●Voltage: 24V

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

-Uses awning fabric that is sturdy and has excellent water repellency
●Size: length 820mm x width 500mm x height 600mm

●Applicable engine size: 175 to 250 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine to select the correct size.

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

●Uses awning fabric that is sturdy and has excellent water repellency.

-Size: length 740mm x width 460mm x height 580mm

●Applicable engine size: 115 to 150 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine.

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

-Uses awning fabric that is sturdy and has excellent water repellency

●Size: length 680mm x width 400mm x height 530mm

●Applicable engine size: 60 to 100 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine to select the correct size.

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

-Uses awning fabric that is sturdy and has excellent water repellency

●Size: length 620mm x width 360mm x height 490mm

●Applicable engine size: 30 to 60 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine to select the correct size.

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

-Uses awning fabric that is sturdy and has excellent water repellency

●Size: length 560mm x width 300mm x height 400mm

●Applicable engine size: 15 to 30 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine to select the correct size.

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

-Uses awning fabric that is sturdy and has excellent water repellency

●Size: length 520mm x width 270mm x height 320mm

●Applicable engine size: 15 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine to select the correct size.

●It is a fire extinguishing bucket that can be folded compactly as it is made of cloth.

●Required during ship inspection.

●It can quickly draw water in an emergency and can be stored compactly, so it does not take up much space.

●JCI standard compliant product No. 17

【 body size 】
■Diameter: Approximately 230mm
■Height: Approx. 265mm

With 3m polyethylene rope

●It is a navigation light that is raised when a ship's operation becomes inconvenient.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLE-4B2

●Type approval number No. 5186

●Light source: light bulb

●Rated voltage: 24V・Rated power: 30W

●Size: Ф90×H109mm

●Made by Koito Seisakusho Co., Ltd.

*Two Class 2 Red Lanterns are required. (Excluding those with a total length of less than 12m) Also, this is a sign that is displayed when operation is inconvenient, and please do not use it for any other purpose.

●It is a navigation light that is raised when a ship's operation becomes inconvenient.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLE-4A2

●Type approval number No. 5185

●Light source: light bulb

●Rated voltage: 12V・Rated power: 30W

●Size: Ф90×H109mm

●Made by Koito Seisakusho Co., Ltd.

*Two Class 2 Red Lanterns are required. (Excluding those with a total length of less than 12m) Also, this is a sign that is displayed when operation is inconvenient, and please do not use it for any other purpose.

●Class 2 tricolor lights and Class 2 white lights apply to sailing vessels less than 12m in total length.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLC-4AB2

●Type approval number No. 5187

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 8W

●Size: Ф111×H282mm

●Made by Koito Seisakusho Co., Ltd.

●This is a light that is attached to the stern (stern) part of a ship.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLS-4AB2

●Type approval number No. 5182

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●This is a light that is attached to the mast of a ship.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLM-4AB4

●Type approval number No. 5181

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●This is a light that is attached to the mast of a ship.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLM-4AB3

●Type approval number No. 5184

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●A navigation light installed on the port side of a ship.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLL-4AB2

●Type approval number No. 5180

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●A navigation light installed on the starboard side of a ship.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLR-4AB2

●Type approval number No. 5179

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●It is a navigation light that must be turned on when the vessel is at anchor.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLA-4AB2

●Type approval number No. 5178

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●Outer diameter: 62mm

●Inner diameter: 22mm

●Bolt: Hole diameter 6mm

●Thickness: 1mm

●The special packing is an anti-vibration rubber packing that is installed between the boat light and the installation pedestal, etc., and is recommended to prevent damage to the main unit.

●Special packing for ship lights (manufactured by Ibuki Kogyo Co., Ltd.) that comply with the new standards.

*Product images are for illustrative purposes only and may differ from the actual product.

[Compatible boat lights] Manufactured by Ibuki Kogyo Co., Ltd.
・Third class mast light Product number: 35262 (Manufacturer product number: NLSM-3W)
・Second class sidelight left red Product number: 35263 (Manufacturer product number: NLSG-2R)
・Second class sidelight right green Product number: 35264 (Manufacturer product number: NLSG-2G)
・Second-class dual-color light Product number: 35265 (Manufacturer product number: NLSW-2B)
・Second class stern light Product number: 35266 (Manufacturer product number: NLSS-2W)
・Second class white light Product number: 35267 (Manufacturer product number: NLSA-2W)
・Second class red light Product number: 35266 (Manufacturer product number: NLSA-2R)