Collection: Fuel related

Clamps are mainly used on automobile and motorcycle production lines.
Made entirely of stainless steel, it has excellent corrosion resistance and durability.
Long screw design improves workability,
The liner design has a carefully calculated structure that prevents the rubber hose from protruding from the inside.
Easy to use as it is a bolt with a minus groove!
■Domestic production

■Material: Stainless steel SUS304
■Quantity: 2 pieces 1 set

Please select your desired size.
JL800610: Φ8～10mm
JL800612: Φ10~12mm

●10 pieces

●Hose outer diameter:

16mm…for 5/16

18mm…for 3/8

24mm…For primer pump

■Material: T bolt, nylon nut all made of stainless steel

[Product specifications]
■Tightening range/clamp width/quantity

JL52-635714: 63.5~71.4mm / 19.0mm / 1 piece
JL52-826905: 82.6~90.5mm / 19.0mm / 1 piece
JL52-11431222: 114.3~122.2mm / 19.0mm / 2 pieces
JL52-15241651: 152.4~165.1mm / 19.0mm / 1 piece

Definitely recommended for models with a supercharger.
Traditional hose clamps will collapse if you tighten them too much, and fall out if you don't tighten them too much...
There was such a problem, but the tightening torque can now be managed.

With heavy duty high torque clamp,
Boasts torque performance more than three times that of normal worm gear clamps.
It is mainly used in exhaust and intake areas where vibration is likely to occur.
Tighten the T-bolt with a lock nut, so you don't have to worry about it coming loose.
It also has a structure that tightens the hose evenly, so you can grip the hose firmly.

The bolts and nuts are also made of rust-resistant SUS.
The nut uses a stainless steel nylon nut that is hard to loosen.
Adopts a ROLLED-EDGE design (R processing on both ends of the band makes it difficult for the hose to get wedged).

■Material: Stainless steel

[Product specifications]
■Size/Quantity
JL51-110133: 11.0~13.3mm / 10 pieces
JL51-155185: 15.5-18.5mm / 10 pieces
JL51-194226: 19.4~22.6mm / 10 pieces
JL51-224256: 22.4~25.6mm / 10 pieces
JL51-256320: 25.6-32.0mm / 10 pieces
JL51-436500: 43.6~50.0mm / 10 pieces
JL51-700780: 70.0~78.0mm / 10 pieces

Clamp using a special tool (product number: CH-207).
The clamping capacity is much greater than that of normal tightening clamps.
Used in SEADOO superchargers and important parts that must not come loose.

■Material: Stainless steel
■Quantity: 5 pieces
■Size: 90-110mm

Compared to standard stainless steel clamps, there are no holes in the groove (zebra-like),
You can apply more tightening torque than standard clamps.

■Material: Rust-resistant stainless steel

[Product specifications]
■Size/Quantity
JL50-120140: 120-140mm / 2 pieces
JL50-140160: 140-160mm / 2 pieces
JL50-1625: 16-25mm / 10 pieces
JL50-4060: 40-60mm / 10 pieces
JL50-6080: 60-80mm / 5 pieces
JL50-816: 8~16mm / 10 pieces

Compared to standard stainless steel clamps, there are no holes in the groove (zebra-like),
You can apply more tightening torque than standard clamps.

[Product specifications] All stainless steel hose clamp

 ■Material: Stainless steel

■Size/Quantity
7~16mm / 10 pieces
10~23mm / 10 pieces
16~32mm / 10 pieces
33~57mm / 10 pieces
47~70mm / 10 pieces
59~82mm / 5 pieces
71~95mm / 5 pieces
91~114mm / 5 pieces
118~140mm / 5 pieces

Nozzle hose for stainless steel portable cans

■ Total length: 250mm
■Product numbers for which compatibility has been confirmed: JL15006-20, JL15006-25
*This product is shorter than the nozzle hose that comes with the JL15006 stainless steel portable can. Please check the size.

Aluminum cap for stainless steel cans

■Material: Aluminum
■Compatibility confirmed product part numbers: JL15006-20, JL15006-25

Bent bolt for stainless steel cans

■Compatibility confirmed product part numbers: JL15006-20, JL15006-25

UN standard certified product Fire service law compliant product

Made of rust-resistant stainless steel, it will stay shiny even after many years of use.

●Uses a large handle for smooth operation during refueling.
●The poly injection nozzle can be stored inside when not in use.
●It has three handles with a unique structure, so it can be carried by one person or by two people from the left and right sides.

[Product specifications]

■Material: Body/stainless steel Cap/aluminum
■Size: Width 255x Length 360x Height 320mm
■Accessories: Aluminum cap, nozzle hose, vent bolt (all assembled)
■Instruction manual

[Repair parts] Refueling cap, nozzle hose, and vent bolt (ventilation screw) are also sold separately.

This is a fuel hose used to connect between the fuel tank, primer, and engine.

■Total length: 30m
■Hose inner diameter: 3/8 (9.5mm)

This is a fitting that is attached to the outboard motor fuel tank to take out the fuel.

■Compatibility: For Suzuki outboard motors (75hp or less)
■Tank part screw size: 1/4”NPT
■Caliber: 11mm

Fitting attached to the fuel tank side hose for outboard motors

■Compatibility: For Suzuki outboard motors (75hp or less)
■Compatible hose: 5/16” (inner diameter 8mm) hose compatible
■Caliber: 11mm

Secures to a hose with an inner diameter of 8mm using a clamp (sold separately).

Can be installed and removed with one touch on the tank side fitting.

This is a fitting that is attached to the fuel tank of an outboard motor to take out the fuel.

■Type: Tank side fitting

■Compatibility: For Yamaha outboard motors 1/4”NPT

■Tank part screw size: 1/4 inch diameter 13mm

* Regarding compatibility with YAMAHA outboard motors, even if the outboard motor is compatible, the caliber may be different and it may not be possible to use the product. For fitting compatibility, please check the diameter shape before making your selection.

■This is a fitting attached to the outboard motor fuel tank side hose.

■Can be installed and removed with one touch on the tank side fitting.

■Compatibility: 3/8” hose 8894-7 for Yamaha outboard motors

■Hose compatible size: Compatible with inner diameter 9.5mm hose

*Fix to a hose with an inner diameter of 9.5 mm using a clamp sold separately.

* Regarding compatibility with YAMAHA outboard motors, even if the outboard motor is compatible, the caliber may be different and it may not be possible to use the product. For fitting compatibility, please check the diameter shape before making your selection.

■Compatibility: 3/8” hose 8902-7 (17660-ZV5A00) for Honda outboard motors
■Compatible with 9.5mm inner diameter hose

Fitting for outboard motor fuel tank hose
Secures to a 9.5mm inner diameter hose with an optional clamp.
It can be attached and removed with one touch to the tank side fitting.

*The fitting for the outboard motor side is part number: 99522.

■Compatibility: 1/4” NPT 8901-7 (16977-ZV5A00) for Honda outboard motors
■Tank part screw size: 1/4 inch outer diameter 13mm

This is a fitting that is attached to the fuel tank of an outboard motor to take out the fuel.

■Compatibility: For Honda outboard motors (from 2001) 3/8” hose 8900-7 (17650-ZW9-003)
■Compatible with 9.5mm inner diameter hose

By installing this fitting, the connection to the fuel tank can be installed and removed with one touch.
It is used by securing it to a hose with an inner diameter of 9.5 mm using a clamp.

*The fitting for the tank side hose is part number: 99524.

【please note】
Can only be used with square hole type outboard motors.
Please note that some Honda outboard motors manufactured before or around 2001 have round holes instead of the square holes shown.

This is a fitting that is attached to the fuel tank of an outboard motor to take out the fuel.

■Type: Tank side fitting

■Compatibility: For Suzuki outboard motors (75hp or more) 1/4” NPT

■Tank part screw size: 1/4 inch diameter 13mm

* Regarding compatibility with SUZUKI outboard motors, even if the outboard motor is compatible, the caliber may be different and it may not be possible to use it. Please check the caliber size before making your selection regarding fitting compatibility.

■This is a fitting attached to the outboard motor fuel tank side hose.

■Can be installed and removed with one touch on the tank side fitting.

■Type: Hose side fitting (for diameter: Φ13mm)

■Compatibility: For Suzuki outboard motors (75 HP or more) 3/8” hose

■Hose compatible size: Compatible with inner diameter 9.5mm hose

*Fix to a hose with an inner diameter of 9.5 mm using a clamp sold separately.

* Regarding compatibility with SUZUKI outboard motors, even if the outboard motor is compatible, the caliber may be different and it may not be possible to use it. Please check the caliber size before making your selection regarding fitting compatibility.

[Product specifications]
■Capacity: 6 gallons / 22.7 liters
■Size: L552 x W375 x H267mm (*Height is up to the cap surface)
■Gauge is included with the main unit

【please note! ]
Since this product does not comply with the Fire Service Act, it cannot be refueled directly from a gas station.
Please use after transferring from a tank that is certified by the Fire Service Act.

*Hose mounting fittings are not included with this tank. Please purchase separately.
The fittings installed on the tank vary depending on the outboard motor manufacturer.

A high-density polyethylene fuel tank for outboard motors.
Since it is made of polyethylene, there is no need to worry about rust and it is resistant to corrosion.

■Capacity: 12 gallons / 45 liters
■Size: Length 610 x Width 450 x Height 255mm

[Information regarding delivery]
・Due to the shape of the product, it cannot be bundled with other products.
・One small parcel is delivered per item, and from the second item onward, shipping fee x (number of items) will be charged.

【please note! ]
Since this product does not comply with the Fire Service Act, it cannot be refueled directly from a gas station.
Please use after transferring from a tank that is certified by the Fire Service Act.

*Hose mounting fittings are not included with this tank. Please purchase separately.
The fittings installed on the tank vary depending on the outboard motor manufacturer.

A high-density polyethylene fuel tank for outboard motors.
Since it is made of polyethylene, there is no need to worry about rust and it is resistant to corrosion.

■Capacity: 12 gallons / 45 liters
■Size: Length 575 x Width 355 x Height 330mm

[Information regarding delivery]
・Due to the shape of the product, it cannot be bundled with other products.
・One small parcel is delivered per item, and from the second item onward, shipping fee x (number of items) will be charged.

【please note! ]
Since this product does not comply with the Fire Service Act, it cannot be refueled directly from a gas station.
Please use after transferring from a tank that is certified by the Fire Service Act.

*Hose mounting fittings are not included with this tank. Please purchase separately.
The fittings installed on the tank vary depending on the outboard motor manufacturer.

■A manual fuel delivery pump that is convenient when starting an outboard engine.

■Compatible with hose inner diameter 3/8 (9.5mm)

[About the product]
Please note that the product color may differ depending on the arrival time.

■This is a fuel hose that comes with a pump (primer pump) for manually dispensing fuel, which is convenient when starting an outboard engine.

■Used to connect between the fuel tank and engine.

■Total length: 1.9m

■Hose inner diameter: 3/8 (9.5mm)

■This is a hose side fitting attached to the fuel tank side fitting.

*Please use with tank fitting (product number: 30018) sold separately.

■Compatibility: TOHATSU outboard motor 2-stroke 3/8” hose

■Fix to a hose with an inner diameter of 9.5mm using a clamp sold separately.

■Can be installed and removed with one touch on the tank side fitting.

■It is a fitting that is attached to the fuel tank.

*Please use with hose fitting (product number: 30019) sold separately.

■Compatibility: TOHATSU outboard motor 2-stroke 1/4”NPT

■Tank part screw size: 1/4 inch outer diameter 12.5mm

●This tank is JCI (Small Ship Inspection Institute) certified product.
●High-density polyethylene fuel tank for outboard motors.
●There is no need to worry about rust, and it is resistant to corrosion, so it can be used as a spare or an extension depending on the space on the ship.

[Product specifications]
■Capacity: 3 gallons / 11.3 liters
■Size: Length 360 x Width 270 x Height 235mm
■Air vent cap
■See-through type (no fuel gauge)

【please note! ]
Since this product does not comply with the Fire Service Act, it cannot be refueled directly from a gas station.
Please use after transferring from a tank that is certified by the Fire Service Act.

*Hose mounting fittings are not included with this tank. Please purchase separately.
The fittings installed on the tank vary depending on the outboard motor manufacturer.

●High-density polyethylene fuel tank for outboard motors.
●There is no need to worry about rust, and it is resistant to corrosion, so it can be used as a spare or an extension depending on the space on the ship.

[Product specifications]
■Capacity: 6 gallons / 22.7 liters
■Size: Length 590 x Width 300 x Height 235mm
■Air vent cap with gauge

【please note! ]
Since this product does not comply with the Fire Service Act, it cannot be refueled directly from a gas station.
Please use after transferring from a tank that is certified by the Fire Service Act.

*Hose mounting fittings are not included with this tank. Please purchase separately.
The fittings installed on the tank vary depending on the outboard motor manufacturer.

●High-density polyethylene fuel tank for outboard motors.
●There is no need to worry about rust, and it is resistant to corrosion, so it can be used as a spare or an extension depending on the space on the ship.

[Product specifications]
■Capacity: 3 gallons / 11.3 liters
■Size: Length 360 x Width 270 x Height 235mm
■Air vent cap
■See-through type (no fuel gauge)

【please note! ]
Since this product does not comply with the Fire Service Act, it cannot be refueled directly from a gas station.
Please use after transferring from a tank that is certified by the Fire Service Act.

*Hose mounting fittings are not included with this tank. Please purchase separately.
The fittings installed on the tank vary depending on the outboard motor manufacturer.

●An air vent and O-ring set exclusively for stainless steel portable cans.
●Please use as a spare or in case of damage or loss.

*AB-10 / AB-10F / AB-20 / AB-20F Stainless steel carrying cans only
Repair Parts

●Aluminum cap exclusively for stainless steel cans.
●Please use as a spare or in case of damage or loss.

*AB-10 / AB-10F / AB-20 / AB-20F Stainless steel carrying cans only
Repair Parts

●This is a set of bellows nozzle and gasket for stainless steel portable cans.
●Please use as a spare or in case of damage or loss.

Nozzle spout (tip) dimensions:
Inner diameter: approx. 19-20mm
Outer diameter: approx. 22-23 mm
Pipe length: 24cm

*AB-10 / AB-10F / AB-20 / AB-20F
Repair parts for stainless steel portable containers