Collection: outboard motor parts

SUZUKI outboard motor protection anode equivalent to genuine product number "55320-95311"

[Material] Anti-corrosion zinc
[Compatibility] Used in: SUZUKI outboard motor 4-stroke model

●Bracket: DF9.9/15(-'00)

- Clamp bracket: DF25/30 (3 cylinder), DF40/50, DF40A/50A/60AQ specifications (-'14)

●Extension case: DF60/70 (Transom X specification only)

SUZUKI outboard motor genuine protection anode 55321-95J00

[Material] Anti-corrosion zinc
[Compatibility] Used in: SUZUKI outboard motor 4-stroke model

●Cylinder: DF2/DF8A/9.9A

-Cylinder head: DF5A/6A (installed at the back of the thermostat), DF25 (V2)

SUZUKI outboard motor protection anode equivalent to genuine product number "55320-95311"
■1 set of 3 pieces

[Material] Anti-corrosion zinc
[Compatibility] Used in: SUZUKI outboard motor 4-stroke model

●Bracket: DF9.9/15(-'00)

- Clamp bracket: DF25/30 (3 cylinder), DF40/50, DF40A/50A/60AQ specifications (-'14)

●Extension case: DF60/70 (Transom X specification only)

SUZUKI outboard motor protection anode equivalent to genuine product number "55320-94900"

[Material] Anti-corrosion zinc
[Compatibility] Used in: SUZUKI outboard motor 4-stroke model

- Clamp bracket: DF60A (tilt specification only), DF60/70, DF70A/80A/90A, DF90/100/115/140/100A/115A/140A, DF150/175/150TG/175TG, DF200A/200AP, DF200/225 /250・DF300/250AP/300AP

SUZUKI Outboard Motor Protection Anode Equivalent to genuine part number "55320-94900" ■1 set of 2

[Material] Anti-corrosion zinc [Compatibility] Used in: SUZUKI outboard motor 4-stroke model

- Clamp bracket: DF60A (tilt specification only), DF60/70, DF70A/80A/90A, DF90/100/115/140/100A/115A/140A, DF150/175/150TG/175TG, DF200A/200AP, DF200/225 /250・DF300/250AP/300AP

SUZUKI outboard motor aftermarket product Protection anode Equivalent to genuine product number "55321-87J01"

[Material] Anti-corrosion zinc
[Compatibility] Used in: SUZUKI outboard motor 4-stroke model

-Gear case: DF2, DF5, DF5A/6A, DF8A/9.9A, DF9.9B/15A/20A, DF70A/80A/90A

-Drive shaft housing: DF5/DF25(V2)/DF60AV

-Cylinder head: DF8A/9.9A, DF9.9B/15A/20A, DF40/50('05-), DF40A/50A/60A/60AV, DF70A/80A/90A, DF90(421060-), DF115(421141-) )・DF150/175/150TG/175TG・DF200A/200AP・DF200/225/250・DF300/250AP/300AP

-Cylinder block: DF40/50・DF40A/50A/60A/60AV・DF100A(510032-)・DF115A(510411-)・DF140A(510550-)・DF150/175/150TG/175TG・DF200A/200AP

- Clamp bracket (PTT specification only): DF9.9B/15A/20A, DF25(V2), DF25A/30A, DF40A/50A/60AQ specification ('15-), DF60AV

●Swivel bracket: DF9.9B/15A/20A (PTT specification + transom L/X only)・DF25(V2)・DF25A/30A・・DF150/175/150TG/175TG

-PTT (PTT specification only): DF9.9B/15A/20A, DF25/30 (3 cylinder), DF25A/30A, DF40/50 ('01-), DF40A/50A/60A/60AV, DF60/70 (' 01-)

●Oil pan: DF25(V2)・DF200A/200AP・DF200/225/250・DF300/250AP/300AP

●Case, extension (LL specification only):・DF25(V2)

-Gas assist (gas assist specification only):・DF25(V2)・DF25/30(3 cylinder)・DF25A/30A・DF40/50('01-)・DF40A/50A/60A/60AV

-Exhaust cover: DF25/30 (3 cylinders), DF70A/80A/90A, DF150/175/150TG/175TG, DF200/225/250, DF300/250AP/300AP

●Exhaust manifold: DF25A/30A・DF60/70
●Extension case: DF70A/80A/90A (transom X specification)
●Rectifier: DF90/100/115/140/100A/115A/140A
●Propeller shaft housing: DF300(-'11)

SUZUKI outboard motor aftermarket product Protection anode Equivalent to genuine product number "55321-87J01" ■1 set of 5 pieces

[Material] Anti-corrosion zinc [Compatibility] Used in: SUZUKI outboard motor 4-stroke model

-Gear case: DF2, DF5, DF5A/6A, DF8A/9.9A, DF9.9B/15A/20A, DF70A/80A/90A

-Drive shaft housing: DF5/DF25(V2)/DF60AV

-Cylinder head: DF8A/9.9A, DF9.9B/15A/20A, DF40/50('05-), DF40A/50A/60A/60AV, DF70A/80A/90A, DF90(421060-), DF115(421141-) )・DF150/175/150TG/175TG・DF200A/200AP・DF200/225/250・DF300/250AP/300AP

-Cylinder block: DF40/50・DF40A/50A/60A/60AV・DF100A(510032-)・DF115A(510411-)・DF140A(510550-)・DF150/175/150TG/175TG・DF200A/200AP

- Clamp bracket (PTT specification only): DF9.9B/15A/20A, DF25(V2), DF25A/30A, DF40A/50A/60AQ specification ('15-), DF60AV

●Swivel bracket: DF9.9B/15A/20A (PTT specification + transom L/X only)・DF25(V2)・DF25A/30A・・DF150/175/150TG/175TG

-PTT (PTT specification only): DF9.9B/15A/20A, DF25/30 (3 cylinder), DF25A/30A, DF40/50 ('01-), DF40A/50A/60A/60AV, DF60/70 (' 01-)

●Oil pan: DF25(V2)・DF200A/200AP・DF200/225/250・DF300/250AP/300AP

●Case, extension (LL specification only):・DF25(V2)

-Gas assist (gas assist specification only):・DF25(V2)・DF25/30(3 cylinder)・DF25A/30A・DF40/50('01-)・DF40A/50A/60A/60AV

-Exhaust cover: DF25/30 (3 cylinders), DF70A/80A/90A, DF150/175/150TG/175TG, DF200/225/250, DF300/250AP/300AP

●Exhaust manifold: DF25A/30A・DF60/70
●Extension case: DF70A/80A/90A (transom X specification)
●Rectifier: DF90/100/115/140/100A/115A/140A
●Propeller shaft housing: DF300(-'11)

NGK spark plug BPR5ES for HONDA BF5A outboard motor

[BPR5ES compatible model]
BF5A

●Sold in units of one. Please purchase as many as you need.

*The image is an image photograph.

NGK spark plugs for outboard motors

[LKR6E compatible model] DF200A/200AP

● Sold in single units
*The image is an illustrative image.

NGK spark plug for outboard motors

[BPR6ES]
SUZUKI Suzuki outboard motor compatible models: DF5 (~'10 MODEL)/DF60/DF70

●Sold in units of one. Please purchase as many as you need.

*The image is an image photograph.

NGK spark plug for outboard motors

[BKR6E compatible model]
DF90・115・140・175・200・225・250
DF9.9/15 ('04-'10 MODEL)
DF25 (V2)
DF90/100/115/140/100A/115A/140A
DF150/175/150TG/175TG
DF200/225/250

●Sold in units of one. Please purchase as many as you need.

*The image is an image photograph.

■Advanced Plus/Special Set

[Set contents] Boat + 5 items ★ 3m inflatable boat (SV-IBA300)
・HONDA 2 horsepower outboard motor (BF2DH-SCHJ)
・HONDA Engine Oil 0.2L (08211-99959)
・Outboard motor stand (JP-HR001)
・5L plastic can (37565)
・High pressure pump (27790)

■Model without preliminary inspection■An inflatable boat that does not require a license or boat inspection if it is equipped with a 2 horsepower outboard motor.
■The transom is 50mm higher than usual, allowing for greater speeds even with the same horsepower.
■One bench mat is included so you can decorate the aluminum bench.
*The color of the bucket in the product image is only an image, so you cannot specify the color.

[Boat specifications]
■Material: PVC
■Capacity: 4 people ■Load capacity: 500kg
■ Overall length x overall width x tube diameter: 300 x 150 x 42 cm
■Inboard length: 182cm
■Interior width: 73cm
Total weight: 34kg
■Bottom type: High pressure air floor ■Maximum horsepower: 10HP
■1 year warranty

[Standard accessories] 7-piece aluminum oar set x 2 (pair),
Carry case,
Foot pump,
Aluminum bench (seating board) x 2,
Bench mat x 1,
SAVIVE original bucket,
Repair kit

[Notes about outboard motor stands]
*Assembly of the hull air stand is required.
*Please note that the color of the transom holder plate may vary depending on the time of arrival.

■Model without preliminary inspection ■Inflatable boat that requires no license or boat inspection if equipped with a 2 horsepower outboard motor.
■The transom is 50mm higher than usual, which increases speed even with the same horsepower.
■One bench mat that can be used to decorate an aluminum bench is included.
*The color of the bucket in the product image is for illustrative purposes only, so you cannot specify the color.

[Boat specifications]
■Material: PVC
■Capacity: 4 people ■Loading capacity: 500kg
■Full length x full width x tube diameter: 300 x 150 x 42cm
■Inboard length: 182cm
■Inner width: 73cm
■Total weight: 34kg
■Bottom type: High pressure air floor ■Maximum horsepower: 10HP
■1 year warranty included

[Standard accessories] 7-piece set aluminum oars x 2 (pair),
carry case,
foot pump,
Aluminum bench (seat board) x 2,
Bench mat x 1,
SAVIVE original bucket,
repair kit

■Advance Plus/Entry Set

【set content】
・3m inflatable boat (SV-IBA300)
・SUZUKI 2 horsepower outboard motor (DF2S)
・SUZUKI engine oil 1L (99000-22B60-4T1)
・Outboard motor stand (JP-HR001)

■Model without preliminary inspection ■Inflatable boat that requires no license or boat inspection if equipped with a 2 horsepower outboard motor.
■The transom is 50mm higher than usual, which increases speed even with the same horsepower.
■One bench mat that can be used to decorate an aluminum bench is included.
*The color of the bucket in the product image is for illustrative purposes only, so you cannot specify the color.

[Boat specifications]
■Material: PVC
■Capacity: 4 people ■Loading capacity: 500kg
■Full length x full width x tube diameter: 300 x 150 x 42cm
■Inboard length: 182cm
■Inner width: 73cm
■Total weight: 34kg
■Bottom type: High pressure air floor ■Maximum horsepower: 10HP
■1 year warranty included

[Standard accessories] 7-piece set aluminum oars x 2 (pair),
carry case,
foot pump,
Aluminum bench (seat board) x 2,
Bench mat x 1,
SAVIVE original bucket,
repair kit

[Note regarding the outboard motor stand]
*The hull air stand requires assembly.
*The plate color of the transom holder varies depending on the arrival time. Please note.

■Advanced Plus/Entry Set

[Set contents]
・3m inflatable boat (SV-IBA300)
・HONDA 2 horsepower outboard motor (BF2DH-SCHJ)
・HONDA Engine Oil 0.2L (08211-99959)
・Outboard motor stand (JP-HR001)

■Model without preliminary inspection■An inflatable boat that does not require a license or boat inspection if it is equipped with a 2 horsepower outboard motor.
■The transom is 50mm higher than usual, allowing for greater speeds even with the same horsepower.
■One bench mat is included so you can decorate the aluminum bench.
*The color of the bucket in the product image is only an image, so you cannot specify the color.

[Boat specifications]
■Material: PVC
■Capacity: 4 people ■Load capacity: 500kg
■ Overall length x overall width x tube diameter: 300 x 150 x 42 cm
■Inboard length: 182cm
■Interior width: 73cm
Total weight: 34kg
■Bottom type: High pressure air floor ■Maximum horsepower: 10HP
■1 year warranty

[Standard accessories] 7-piece aluminum oar set x 2 (pair),
Carry case,
Foot pump,
Aluminum bench (seating board) x 2,
Bench mat x 1,
SAVIVE original bucket,
Repair kit

[Notes about outboard motor stands]
*Assembly of the hull air stand is required.
*Please note that the color of the transom holder plate may vary depending on the time of arrival.

■Advance Plus/Special Set

[Set contents] Boat + 5 items ★3m inflatable boat (SV-IBA300)
・SUZUKI 2 horsepower outboard motor (DF2S)
・SUZUKI engine oil 1L (99000-22B60-4T1)
・Outboard motor stand (JP-HR001)
・5L polyester carrying can (37565)
・High pressure pump (27790)

■Model without preliminary inspection ■Inflatable boat that requires no license or boat inspection if equipped with a 2 horsepower outboard motor.
■The transom is 50mm higher than usual, which increases speed even with the same horsepower.
■One bench mat that can be used to decorate an aluminum bench is included.
*The color of the bucket in the product image is for illustrative purposes only, so you cannot specify the color.

[Boat specifications]
■Material: PVC
■Capacity: 4 people ■Loading capacity: 500kg
■Full length x full width x tube diameter: 300 x 150 x 42cm
■Inboard length: 182cm
■Inner width: 73cm
■Total weight: 34kg
■Bottom type: High pressure air floor ■Maximum horsepower: 10HP
■1 year warranty included

[Standard accessories] 7-piece set aluminum oars x 2 (pair),
carry case,
foot pump,
Aluminum bench (seat board) x 2,
Bench mat x 1,
SAVIVE original bucket,
repair kit

[Note regarding the outboard motor stand]
*The hull air stand requires assembly.
*The plate color of the transom holder varies depending on the arrival time. Please note.

Very convenient for maintenance and storage of outboard motors.
When not in use, it can be folded and stored compactly.

●Material: Steel (black paint)
●Applicable horsepower: Up to 5 horsepower class of 4st outboard motor

●Size: width 540 x depth 640 x height 1000mm
●Outboard motor fixing plate dimensions: width 46 x height 11.5 x thickness 3.5cm
●Height from the top of the outboard motor fixing plate to the ground: Approximately 89.5cm
●Body weight: Approximately 6.0kg

【please note】
*This product requires assembly.
*The plate color of the transom holder varies depending on the arrival time. Please note.

When used by attaching it to a stabilizer, it improves straight-line performance,
Make control safer and easier.

■Quantity: 1 set of 2 pieces of the same color
■Compatible with: Hydrofoil stabilizer exclusive product
→Large type: Compatible with product number 04824 / 21971
→Small type: Compatible with product number 04826 / 21972

[Effect]
●The water flow flowing on the surface dynamically creates upward thrust pressure on the bottom surface of the stabilizer, pushing up the stern and pushing down the bow, shortening the time until planing, increasing propeller efficiency, and improving fuel efficiency!
●The water flow created by the propeller is efficiently pushed backwards, improving controllability and straightness.

●The time until planing is halved, making running and control smoother. It also saves fuel consumption by 10-40%.

[Installation method]
1■ Place the stabilizer on the cavitation plate and mark the 4 places to drill holes.
*At that time, after drilling a hole with a diameter of 6 mm, make sure that there is a gap of at least 1 cm between the edge of the cavitation plate and the edges of all four holes.
*If there is no gap of 1cm or more, the cavitation plate cannot be installed as there is a possibility that it will be damaged while driving.

2■ Use a drill to drill holes with a diameter of 6 mm in four locations, and then pass the included bolts from under the cavitation plate.
*From the bottom, temporarily tighten the 4 places by inserting the bolts → cavitation plate → rubber washer → stabilizer → washer → nut.

3■ Perform final tightening, but instead of final tightening one location at a time, do it diagonally a little at a time, ``evenly in four locations in an X-shaped order.''
4■ Since a locking nut is used, there is no need to tighten the bolts until the stabilizer is deformed.
5■ Move the stabilizer and check that if there is no play, the installation is complete.

【lastly】
Do a test drive and check again to make sure there is no play between the stabilizer and cavitation plate.

[Product specifications]
■Type: Small
■Color: Black / Gray
■Size: Please check the image.
■Correspondence
→Small: 9.9 to 40 horsepower outboard motor

[Effect]
●The water flow flowing on the surface dynamically creates upward thrust pressure on the bottom surface of the stabilizer, pushing up the stern and pushing down the bow, shortening the time until planing, increasing propeller efficiency, and improving fuel efficiency!
●The water flow created by the propeller is efficiently pushed backwards, improving controllability and straightness.

●The time until planing is halved, making running and control smoother. It also saves fuel consumption by 10-40%.

[Installation method]
1■ Place the stabilizer on the cavitation plate and mark the 4 places to drill holes.
*At that time, after drilling a hole with a diameter of 6 mm, make sure that there is a gap of at least 1 cm between the edge of the cavitation plate and the edges of all four holes.
*If there is no gap of 1cm or more, the cavitation plate cannot be installed as there is a possibility that it will be damaged while driving.

2■ Use a drill to drill holes with a diameter of 6 mm in four locations, and then pass the included bolts from under the cavitation plate.
*From the bottom, temporarily tighten the 4 places by inserting the bolts → cavitation plate → rubber washer → stabilizer → washer → nut.

3■ Perform the final tightening, but instead of final tightening one location at a time, do it diagonally a little at a time, ``evenly in four locations in an X-shaped order.''
4■ Since a locking nut is used, there is no need to tighten the bolts until the stabilizer is deformed.
5■ Move the stabilizer and check that if there is no play, the installation is complete.

【lastly】
Do a test drive and check again to make sure there is no play between the stabilizer and cavitation plate.

[Product specifications]
■Type: Large
■Color: Black / Gray
■Size: Please check the image.
■Correspondence
→Large: 40 to 300 horsepower outboard motor, inboard/outboard motor

●Use the outboard motor cleaning flusher by inserting the black rubber part into the cleaning hole.

●With adapter for hose connection

●Perfect fit for YAMAHA bowhole.

Effective in preventing abnormal wear and abnormal noise of each gear in the gear case.

[Contents] 350ml x 1
[Included] Tapered nozzle for oil injection

■Category 4 Petroleum ■Danger class 3
■Viscosity: SAE90 ■Viscosity index: 100
■API classification: GL-4 ■Flash point 216℃
■Pour point -22.5℃
■Heavy viscosity 40℃/176.1, 100℃/16.75
■Hypoid oil

[Contents] 800ml x 1
[Grade] GL-4 #90 High Point Oil
[Included] Tapered nozzle for oil injection

Effective in preventing abnormal wear and abnormal noise of each gear in the gear case.

●This boat dolly is essential for transporting boats.

●The tires are 6 inches in size and are puncture-free tires that do not have to worry about air leaks.

●The angle adjustment pin can be operated with a lever, making it easy to flip up and down with one hand.

●The shaft is made of lightweight aluminum and has been anodized to increase durability.

●The bearing in the rotating part of the tire allows the tire to rotate smoothly.

●With knob screws and special metal fittings, the mounting hardware can be easily removed from the boat. Therefore, the mounting brackets do not get in the way when storing the boat.

●Since the metal fittings are removable, the transom is neat and does not get in the way when stored.

■Tire type: 6 inches ■Total length: 775mm
■Weight (one side): 3.2kg
■Tire load capacity (one side) (kg): 120
■Shaft material: Aluminum (anodized)

●The brass lock (main body: made of brass) prevents theft, making it rust-resistant and durable.

●A set of 5 uses a common key, so you can lock all 5 with one key.

●By inserting the sturdy steel body into the attachment/detachment lever, the outboard motor is prevented from being stolen.

●Material: Corrosion-resistant reinforced steel
(The lock part is made of steel, so please use grease, etc. to prevent it from rusting.)

●With sponge to suppress vibration
-Comes with 2 keys

When used, it eliminates the rear center of gravity when a single person is on a small boat, accelerates the transition to a planing state, and enables stable running.
This is an extension bar that can be attached to the throttle section of an outboard motor or electric motor when the handle is short and difficult to maneuver.

[Installation] Just place it over the grip and tighten the knob! No tools required. Easy to put on and take off.
*If the handle diameter is too small, please adjust it with the included rubber plate.

【Product details】
■Applicability: Ideal for Japanese boats, U-type boats, and fishing boats.
■Material:
→Body: Aluminum
→Other parts: Plastic
■Compatible with: Grip outer diameter: 36-54Φmm
■Telescopic 620-1020mm steplessly adjustable
■With curl cord for extension of kill switch

【please note】
The longer the handle, the worse the turning angle of the handle, so please be careful when maneuvering the boat.

Since it is intended for use with a low horsepower outboard motor, there is a risk of damage if used with a high horsepower outboard motor.
Avoid using outboard motors with more than 15 horsepower.