Collection: UNLIMITED

[Compatible models] Yamaha FX models from 2012 onwards

■Material (pipe): Aluminum

Replaces the restrictive sound suppression system between the water vehicle's water box and the hull exit.
Improves engine performance by reducing back pressure and harmful detonation.
Mandrel-bent aluminum tubing, powder coated to prevent corrosion
A replacement coupler made of high temperature silicone is included.

[Compatible models]
Sea Doo GTI 130 / GTX 170 / GTX 230 / RXT・GTX 300 ALL ('20-)

■Material (pipe): Aluminum

It replaces restrictive sound suppression systems located between the water vehicle's water box and the hull outlet.
It reduces back pressure and harmful detonation, improving engine performance.
Mandrel bent aluminum tubing that is powder coated to prevent corrosion,
Replacement couplers made from high temperature silicone are included.

*For models from 2023 onwards, the Siphon Break Delete Kit ( RS10123-SBD ) is required separately.

[Applicable models] ULTRA310/300 series

●By installing it on the muffler body, it becomes possible to install sensors such as [Product number: AT-200] auto tune.

●Mounting hole: M18xP1.5mm

[Kit contents] Flange body, blind plug, mounting bolts
*Please use genuine gasket.
*Remove the muffler filter before use.

*About 3 weeks after ordering as it is made to order.

[Applicable models] KAWASAKI ULTRA300/310 series

●Remove and use the muffler filter inside the normal muffler.
● Filter maintenance can be omitted by removing the filter.

●Inner diameter Φ60 ⇔ Φ70×Total length 100mm

A silicone coupler with excellent heat resistance, pressure resistance, and oil resistance.
Excellent cost performance and durability.
Can be used as a joint between 60mm and 70mm diameter pipes.

●Inner diameter Φ50⇔Φ70×Total length 100mm

A silicone coupler with excellent heat resistance, pressure resistance, and oil resistance.
Excellent cost performance and durability.

-Inner diameter Ф147 x total length 85mm

Exhaust coupler with excellent heat resistance, pressure resistance, and oil resistance.
Excellent cost performance and durability.

[Adaptation] For KAWASAKI 800X-2

[Regarding processing] Styrofoam cutting of the tank is required (*JCI modification application required)
[Note] This product is not subject to complaints as it is a competition part.

Exhaust pipe made by bending aluminum.
Contributes to approximately 50% (grams) lighter weight and lower center of gravity compared to the genuine rubber tube.
Unlike genuine tubes, there is no expansion due to exhaust temperature, reducing trouble.
Carburetor maintenance is more efficient because the pipes are connected to the bottom of the carburetor.
If you use the T-bolt clamp [Product number: JL0250], there is no need to worry about it coming off.
The joint uses a silicone hose that is highly heat resistant, pressure resistant, ozone resistant, and resistant to deterioration.
■Product weight: 1.3kg

【set content】
Pipe body x 1 set
Joint hose Φ60×70mm×2 pieces
Stainless steel clamp x 2

[Compatible models] KAWASAKI
800SX-R
800X-2

[Product size]
●Outer diameter: 59.65mm
●Total length: 49.15mm
●Minimum inner diameter: 44mm
●Maximum inner diameter: 53mm

Horsepower increases by 1 horsepower just by attaching a sleeve to the stock exhaust line!
The maximum speed has also increased by more than 1km!
We promise improved response and experience in the medium and low speed range.

[Compatible models] KAWASAKI
Exhaust diameter Ф50mm
15F('09-)/ULTRA250X('08)/ULTRA260X/ULTRA LX('09-)

★The following model with exhaust port diameter Ф60mm is part number: JL14001.
STX series ('00-'07) *Excluding 900
STX-R/12F/15F('04-'08)/ULTRA250X('07)/ULTRA300X/ULTRA LX('07-'08)

●Produces a stylish rear exhaust.
●Machined from aluminum (A6061) with excellent strength and corrosion resistance.
●Cover flange with chemically polished alumite processing and excellent design.

[Compatible models] KAWASAKI
JL14001: Exhaust port diameter Ф60mm
STX series ('00-'07) *Excluding 900
STX-R/12F/15F('04-'08)/ULTRA250X('07)/ULTRA300/310/ULTRA LX('07-'08)

★The following model with exhaust port diameter Ф50mm is part number: JL14002.
15F('09-)/ULTRA250X('08)/ULTRA260X/ULTRA LX('09-)

●Produces a stylish rear exhaust.
●Machined from aluminum (A6061) with excellent strength and corrosion resistance.
●Cover flange with chemically polished alumite processing and excellent design.

[Compatible models] SEA-DOO
GTX-4TEC / RXT / RXT-X(-08)

Luxurious stainless steel buffed mirror finish.
Upgrade your visuals by replacing the cheap genuine hook with a polished one!

【correspondence】
KAWASAKI genuine mount (not compatible with some models)
UNLIMITED MOUNT

Standard handlebar 22.4mm diameter

[Material] Aluminum

This is a clamp to hold the handlebars. The clamp is attached at 60.5 degrees. Handlebars
Looking at the installation position from a 60.5° angle, offset it 25 mm upward and 15 mm forward and backward.

[Compatible] Fat bar 28.6mm diameter

*22.4mm handlebar (standard) can also be used with handlebar spacer (product number: UL35002)

[Material] Made of aluminum

Clamp for attaching handlebars.
Since the mounting part is flat, it can be used with Kawasaki genuine mount and UNLIMITED mount.
When installed on the Kawasaki genuine handlebar mount, the handlebar mounting position will be increased by 20mm.

■Correspondence:
KAWASAKI 4 stroke model
SEA-DOO 4 stroke model

■Application: Tool to apply lubrication to the throttle body to prevent it from sticking.

●A must-have item for those riding in seawater!
●Inject lubricant to prevent the throttle body from sticking.

[About installation]
It is necessary to make a hole in the intake pipe using a drill. Install it in front of the genuine throttle body.

[Application] KAWASAKI 750/800 electrical box [Quantity] Blue 1 piece

By replacing the genuine plastic cap, it becomes an accent of the engine room.
With O-ring

For fat bar (tapered handle) only

■Size: 15cm

【correspondence】
runabout model
Compatible with 28.6mm handle clamp
*A separate fat bar clamp (UL061 recommended) is required for installation.

■Handle diameter: Clamp mounting part 28.6mm,
■Grip lever mounting part 22.±0.2mm

A wide handle with a thick clamp part and excellent flexibility and strength.

●A separate throttle adapter (product number: UL002-) is required for installation.
*Kawasaki…Only models before 1995 can be installed without an adapter.

The shape of the tip provides a finger feel that enables fine throttle work!
It is an angled type with the lever tilted 4 degrees downward.

You can adjust the length of the wire and the weight of the throttle.
UNLIMITED handlebar mount switch case (product number: UL014/UL015) can also be used.

■Machined aluminum
■Angle type 4°

[Applicable models] KAWASAKI *Excluding ULTRA 4 stroke (ULTRA310/300/260/250/LX)

About SEADOO boats and YAMAHA boats...
By installing and using the company's fuel filler (UL53005),
KAWASAKI "UNLIMITED billet fuel cap [UL030, UL036]" can be used

Machined aluminum

Kawasaki 800SX-R

Compared to genuine products, they are lighter, stronger, and cheaper.
When worn, it creates a streamlined and lacy impression.

[Material] FRP
[Quantity] 2 pieces 1 set
[Installation] Bolt-on

[Information regarding delivery]
・Due to the shape of the product, it cannot be bundled with other products.

[Compatible models]
■Kawasaki: 750SX / SXi / SXi-Pro / 800X-2 / SX-R series (800SX-R / 1500SX-R)
■YAMAHA: 700FX / 700SJ

[About processing]
[1] When installing on a YAMAHA boat...If using a genuine YAMAHA lock: Machining of the lock part is required. A genuine KAWASAKI lock was purchased separately, and a genuine part lock assembly [27016-3703] was prepared and assembled.
[2] Use on KAWASAKI boats: Disassemble the genuine lock and assemble it to the product.

[Material] Stainless steel buffed finish

Excellent strength! Will not rust!
Replacing the original one will give the hull a luxurious feel and accent, making it more stylish.
The long hook design helps to securely lock the hood and prevent it from coming off.
The hook part can also be used with YAMAHA locks (processing required for installation)

[Note] Only the latch, internal parts of the lock part are not included.

[Adaptation] External handlebar

*When used with SEA-DOO genuine handlebars...
[Product number: UL31004 handlebar extender] is required.

[Quantity] 2 pieces 1 set

It prevents the grip of a personal watercraft from slipping off and makes the handlebar part look stylish.
Made of aluminum material for strength and smooth cut.

■Pattern: Diamond ■Color: Black ■Size: 89 x 119 cm

This reinforced mat eliminates the surface tension of water, allowing for smooth drainage from the deck and providing excellent grip.
Since it is a sheet type, it can be cut freely to create your own original design.

Note: Adhesive is required for attachment.

■Pattern: Border ■Color: Black ■Size: 89 x 119 cm

This reinforced mat eliminates the surface tension of water, allowing for smooth drainage from the deck and providing excellent grip.
Since it is a sheet type, it can be cut freely to create your own original design.

[Note] Adhesive is required for attachment.

KAWASAKI
750SX
800SX-R
800X-2

●Lightweight flywheel weighing 800g.
●The response of engine revving and rotation return is improved, so acceleration from 0 to 1m is significantly improved, making it a must-have item at the start of a racing scene.
●Improved from previous products to increase durability.
●Compatible with CDI-10R/CDI-R power unit, and when installed at the same time, the pickup will be improved and the response will be linear with throttle work. The strength of the gear has also been increased.
●Compatible with battery ignition CDI, so it can be used with KAWASAKI 800SX-R (A2~)/800X-2 with genuine CDI.

【please note】
Since the stator is removed during installation, there is no charging function.

[Compatible models] KAWASAKI STX-R / Ultra150
[Specifications] Compatible with regular gasoline

This is a purely domestic CDI unit, and we have researched the engine characteristics of STX-R/Ultra150 to achieve the best ignition characteristics.
Easy to install and shortens the time to reach top speed from low speed.

[About installation]
Bolt on.
*Please set according to the engine specifications and driving conditions.

[Compatible models]
KAWASAKI 750(B)/800

An indispensable item for crank maintenance and racing scenes.

Made using the same material as the normal one and made it even stronger.
The balance of the crank is the best.
■Made in Japan

*With big end bearing and small end bearing sold separately.

■Compatible with: KAWASAKI Kawasaki
ULTRA 250/260/300/310 series

■Material: Stainless steel
■Application: Remove exhaust manifold

Existing wrenches interfere with the hull, making them difficult to work with and prevent bolts from turning smoothly.
A dedicated angle extension wrench to solve these problems.

"Mirror finish" with a focus on strength and visuals,
This is a product that will shine even in your tool box.

JL15001SL Silver
JL15001GD Gold
JL15001R Red
JL15001OR Orange
JL15001LG Lime Green

●Outer diameter: approx. 8mm
●Inner diameter: approx. 5mm
●Length: Approximately 100cm

[Compatible models] KAWASAKI
SX-R1500 NEW SX-R
800SX-R
SXi-Pro/SXI/SX

handle pole spring
By attaching it with a spring that is approximately 70% stronger than the original, the handle pole weight is reduced by 60%, reducing the burden.
This is an essential item when using the genuine handle pole.

【set content】
●NO.714256: Transom tie down ●NO.ULT131BK-L x 2: Tie down pad L size (250 x 290mm)

Secure to the rear of the trailer using mounting hardware.
The belt wound inside the housing can be stretched to any desired length.
Hang the hook on the transom handle (eye) of the boat, wrap it with a ratchet, and secure it.
Unlike regular tie-down belts, there is no need to take them on and off the trailer every time.
[Mounting brackets (e.g. SRX-143L, SRX-143R)]

●Material: Stainless steel (metal parts)
●1 set of 2 ●Belt width: 48mm x length ~ 900mm
●Load capacity: 3000LBS (1360kg)/2 pieces *The hook in the image is not included. (Image of use in conjunction with multi-hook made by other companies)

Stainless steel tie-down belt ratchet type automatic winding trailer