Collection: Newest Products

■Material: Stainless steel (SUS316)
■Size
Total length 308 x stop hole ~ stop hole 122 x height 68 mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

■Roller diameter (A): 89.0mm
■Width (B): 295.0mm
■Shaft diameter (C): 16.0mm

■Roller diameter (A): 75.6mm
■Width (B): 99.0mm
■Shaft diameter (C): 16.0mm

-Size: width 165 x height 100 x (base 76 x 76mm)
●Good because it's made of rubber so it won't scratch the hull!

■Mounting frame: up to 76.2 x 127mm
■Material: Steel/galvanized
■Maximum load: 680kg / 1500LBS
■Stroke: 300mm
■Wheel diameter: 6" double / 152.4mm

It makes it easy to put on and take off with minimal strain.

■Material: Steel plated

【please note】
Coupler handle only.
Other items used in the photo are not included.
Mounting bolts are not included.

[Product specifications]
■Material: Stainless steel (SUS304)
■Size:
Total length: 260mm
Pedestal dimensions: 85x57mm
■Holder inner diameter
⇒With rubber: 40mm
⇒No rubber: 48mm
[Contents] 5-piece set: rod holder, rubber, stop bolt, intermediate pedestal, and pedestal.

A rod holder that rotates 360° and allows you to freely set the vertical angle according to your preference.
Rubber is pasted on the inside of the rod holder, so there is no need to worry about damaging the rod.

[Product specifications]
■Material (float): PVC foam
■Float body (per piece)
Size: 141φ×175mm
Hole diameter: 25φ
...

■Rope
Size: 12φ×2m

[Float x 3] + [Rope]
●This is a fender that uses egg-shaped vinyl chloride foam in three rows.
●Float body material: PVC foam

A rope specifically designed for towing such as water toy tubes.

■Suitable for approximately 1 to 2 people
■Length 18m
■ Breaking strength: 1,078kg (2,375lbs)

By replacing the hose,
An air pump with excellent cost performance that can be used for both intake and exhaust.
When using on towing tubes, please use a foot pump or hand pump for finishing.
★3 types of adapters are standard equipment

■Voltage/Current AC100V/1.4Amp
■Outlet plug specifications
■Continuous use time approximately 13 minutes
■Air flow rate 510L/min
■Pressure: 1.02psi
■Accessories: 3 types of adapters

A compact, classic donut-shaped towing tube.

■Size: 137cm
■Maximum capacity: 1 person ■1 towing point ■PVC tube & nylon full cover

*Pump and rope are not included.

[JSPTOKAI original square clear bag]
56L large capacity bag that can store 4 life jackets at once
The top can be opened wide with a U-shaped zipper to store marine gear.
The bottom is made of mesh material that allows water to drain.
With this bag, you can solve the problem of carrying and storing goods!
■Size: 50x45x25cm
■Fabric: Clear PVC black mesh

This is a classic and popular glasses type model.
You can tow in two ways: vertically and horizontally, so you can enjoy it twice as much.
Since it is a compact two-person model, it has little air volume and storage space is also small.

■Size: 211×137cm
■Maximum capacity: 2 people ■2 towing points ■PVC tube & nylon full cover

[JSPTOKAI original square clear bag]
56L large capacity bag that can store 4 life jackets at once
The top can be opened wide with a U-shaped zipper to store marine gear.
The bottom is made of mesh material that allows water to drain.
With this bag, you can solve the problem of carrying and storing goods!
■Size: 50x45x25cm
■Fabric: Clear PVC black mesh

[Includes a free JSPTOKAI original bag for convenient storage of supplies!]

This is a round toy with four double grips.
Riding with four people is four times the fun!
It is one of the most compact four-seater vehicles.

■Size: Diameter 188cm
■Maximum capacity: 4 people ■1 towing point ■PVC tube ■Nylon full cover

*Only the main unit; pump and rope are not included.

[JSPTOKAI original square clear bag]
A large 56L bag that can store up to four life jackets at once
The U-shaped zipper allows the top to open wide, allowing you to store marine gear.
The bottom is made of mesh material, so water can drain easily.
With this bag, you can easily solve the problem of carrying and storing your items!
■Size: 50x45x25cm
■Fabric: Clear PVC, black mesh

Have you ever experienced ``slalom speed slowing down due to water resistance'' when the towing rope came into contact with the water surface?
With this booster ball, there is no resistance due to water pressure and you can enjoy free and smooth action.
It is also a plus-one optional item for water toys that eliminates the discomfort of the top sinking when starting.
There are 8.5M ropes on each side of the ball, so the total length is approximately 18M, so if you have this, you won't need a towing rope.

【Product details】
■Ball diameter 69x97cm
■Total length: 18m
■Can be used up to 4-seater type

[Contents] 2L
[How to use] For removing red rust, blue rust on the hull, removing stains from the wood of the deck, and cleaning light oily substances.

It does not cause corrosion damage to painted surfaces or metal surfaces of the hull, and the luster of the hull does not disappear.

▼How to use▼
Wet the area to be cleaned with water before use.
For normal use, dilute it 3 times and adjust the concentration depending on the degree of dirt.
Using rubber gloves, thoroughly soak a brush, sponge, or cloth in detergent and scrub depending on the degree of dirt.
Be sure to rinse thoroughly with plenty of tap water within 2 minutes to ensure that no Hytrail ingredients remain.
Wipe off moisture with a dry cloth.

*Please try it in an inconspicuous place before use.
*Do not leave it on for more than 2 minutes as it may change color.

Notes
・Never use a spray bottle.
・Do not use on glass surfaces such as automobiles or aluminum parts of vehicles.
・Please do not use the product under the blazing sun or when the product is hot, as stains and uneven color may occur and will be difficult to wipe off.
・Please do not use coatings (mirror finishing, etc.) or painted areas as they will peel off.

CASTRO
Castro Fender was born in Spain in the early 1970s by founder Carlos Castro.
Castro is now one of the world's largest manufacturers of buoy fender floats.
Our products are sold in over 70 countries around the world and are widely praised for their outstanding quality and innovative design.

■Size: Diameter/Total length/Eye diameter
A-0HD: 200mm / 270mm / 25mm
A-1HD: 290mm / 370mm / 25mm

●It is a drop-shaped air fender.
●The rope attachment hole is thick and reinforced with ribs, making it extremely durable. ,
●Can also be used as a course buoy if installed upside down.
●You can easily inflate with an air compressor or air gun.

【please note】
*Air injection nozzle not included *Delivered with air removed *As this is an overseas product, specifications may change without notice.

[Product specifications]
■Material: Nylon ■Rope diameter: 1/2 (12.7mm)
■Length: 200ft (60m), 300ft (90m)

An easy-to-handle nylon triple rope with excellent abrasion resistance, strength, and flexibility.

Connect and use with alligator clips.
Because the hose has a large diameter, air can be injected and discharged more smoothly.

【specification】
■Air flow rate: 350L/min
■Voltage: DC12V
■Current: 33Amp
■Maximum pressure: 2.3psi
■Accessories: 2.6m power cord with alligator clip, air hose, 6 types of attachments

●You can inflate everything from large rubber boats to towing tubes, beach balls, and floats.
●By replacing the injection nozzle with the suction port, it can also be used to bleed air from inflated items.
Since most of the air inside the inflatable product can be removed, it can be folded into a small size.
●When using on towing tubes, please use a foot pump or hand pump for finishing.

●An hour meter that detects the ignition signal of the gasoline engine and measures the cumulative operating time of the engine.
●Measurements can be made by simply wrapping the included antenna lead wire around the spark plug cord.
●With reset function to return the count to 0

【Product details】
*Cannot be used with diesel engines and direct ignition types.
■Dimensions: L30 x W30 x H15mm
■Body weight: 15g
■Accessories: Antenna lead wire (50cm)
■Daily waterproof specifications
■Measurement method: Pulse sensing method
■Measurement time: Maximum 9999 hours 59 minutes
■Battery life: Approximately 5 years
■Using temperature: -10℃～+60℃

A coating agent containing fluorine-modified silicone.
For protecting and polishing gel coat surfaces of boats and PWCs!
For reproducing black color and polishing resin moldings and gunwales!

■Construction guideline
Aerosol 420ml, application area: approximately 3 to 5.24 feet 2 bottles for ships, 1 bottle for PWC
■Construction method
1. Remove dirt and debris from the area to be applied with a cleaning agent and dry.
2.Apply Marine Glass Coat and spread it over the entire surface using a cloth such as a microfiber cloth.
3. Let it dry at room temperature for about 3 to 8 hours.

●Marine Glass Coat is a coating agent for ship hulls that contains fluorine-modified silicone.
●By forming a glass-like film on the gel coat or painted surface, it creates a glossy luster, and
The water repellent effect reduces the adhesion of dirt and rust, making subsequent cleaning easier◎
●It cures easily at room temperature, so you can easily apply the coating yourself.
It can be used for FRP, so it can be used not only for boat hulls but also for camper shells etc.

●A trailer jack made of aluminum with a novel design.

●Flat plate type. Foldable type.

■Mounting frame: up to 76.2 x 101.6mm
■Material: Aluminum
■Maximum load: 900kg
■Plate diameter: 178mm

[Product specifications]
●Voltage: 12V
●Current: 3.4A
-External dimensions: 74 x 64 x height 111mm (dimensions in image)
●Drainage volume 50 liters/min
●Compatible with hose diameter 19.0mm
[Adaptation] Ideal for PWC (personal watercraft) and small boats

●Since it is a completely waterproof submersible pump, it is a convenient product for circulating and draining water while on board or during maintenance.
●When wiring, insert a 7.5A fuse (*) on the + cord side.
(*Fuse is not included with this product and must be purchased separately)

[Product specifications]
●Voltage: 12V
●Current: 1.6A
-External dimensions: 74 x 64 x height 99mm (dimensions in image)
●Displacement volume 31 liters/min
●Compatible with hose diameter 19.0mm
[Adaptation] Ideal for PWC (personal watercraft) and small boats

●Since it is a completely waterproof submersible pump, it is a convenient product for circulating and draining water while on board or during maintenance.
●When wiring, insert a 4A fuse (*) on the + cord side.
(*Fuse is not included with this product and must be purchased separately)

●Made by Fulton, a leading American trailer parts manufacturer.

■Maximum towing load: 580kg. 1300LBS.
■Drum winding capacity: Supports strap lengths up to 20FT (approximately 6,096mm)
■With 2-way ratchet lock
■Handle length 22cm
■Material: Main body made of steel

*Cannot be used for vertical movement.
*Strap is sold separately.

●Made by Fulton, a leading American trailer parts manufacturer.

■Maximum towing load: 400kg. 900LBS.
■Drum winding capacity: Supports strap lengths up to 15FT (approximately 4,572mm)
■Handle length 20cm
■Material: Main body made of steel

*Cannot be used for vertical movement.
*Strap is sold separately.

●Two-way ratchet lock with plastic cover.

●Material:
[Body] Steel
[Cover] Plastic
●Maximum towing load: 680kg
●Handle length: 23Cm
●Strap size: Width 2" (approx. 5.08cm) 20FT (approx. 609.6cm)

●Nuperakurin PLUS is a set of antifouling paint for propellers that does not contain chromate compounds and is friendly to people and the environment.

●An epoxy resin primer that has excellent adhesion to the propeller surface that rotates at high speed and forms a strong coating, and a newly formulated silicone resin antifouling paint that exhibits excellent antifouling power even during mooring periods. Prevents marine organisms from adhering to the shaft.

●Note: An electric disc sander is required for construction.
Paper discs #80 to 240, nylon discs, etc. can be used, expanding the scope of work.

[Coating amount] Approximately 0.3 square meters (approximately 25 cm diameter propeller)

【set content】
■Nuperacrine PLUS Primer: Main agent ×1530g
■Nuperakurin PLUS Primer: Hardening agent ×270g
■Nuperacrine PLUS Primer: Adhesion enhancer ×90g
■Nuperakurin PLUS finish: 1000g

【how to use】
1.Remove marine organisms and oil from the propeller.
2.Remove the old paint film and polish the propeller surface using an electric disc sander.
3. Wipe with thinner. (Sea Jet Thinner A, Sea Jet Thinner D, etc.)
4. Apply two coats of Nuperacrine PLUS Primer. (Please complete 2 coats within 90 minutes)
5.After the primer dries, apply Nuperacrine PLUS finish. (Recommended 2 coats or thicker coat)
6. After drying thoroughly, lower the rack. (Over 8 hours at a temperature of 20 degrees)
*For details, please refer to the installation instructions included with the product and the Chugoku Paint Co., Ltd. website.

●Nuperakurin PLUS is a set of antifouling paint for propellers that does not contain chromic acid compounds and is friendly to people and the environment.

●An epoxy resin primer that has excellent adhesion to the propeller surface that rotates at high speed and forms a strong coating, and a newly formulated silicone resin antifouling paint that exhibits excellent antifouling power even during mooring periods. Prevents marine organisms from adhering to the shaft.

●Note: An electric disc sander is required for construction.
Paper discs #80 to 240, nylon discs, etc. can be used, expanding the scope of work.

[Coating amount] Approximately 0.3 square meters (approximately 25 cm diameter propeller)

【set content】
■Nuperacrine PLUS Primer: Main agent ×255g
■Nuperacrine PLUS Primer: Hardening agent x 45g
■Nuperacrine PLUS Primer: Adhesion enhancer ×15g
■Nuperakurin PLUS finish: 160g
■Brush: 2

【how to use】
1.Remove marine organisms and oil from the propeller.
2.Remove the old paint film and polish the propeller surface using an electric disc sander.
3. Wipe with thinner. (Sea Jet Thinner A, Sea Jet Thinner D, etc.)
4. Apply two coats of Nuperacrine PLUS Primer. (Please complete 2 coats within 90 minutes)
5.After the primer dries, apply Nuperacrine PLUS finish. (Recommended 2 coats or thicker coat)
6. After drying thoroughly, lower the rack. (Over 8 hours at a temperature of 20 degrees)
*For details, please refer to the installation instructions included with the product and the Chugoku Paint Co., Ltd. website.

●Nuperakurin PLUS is a set of antifouling paint for propellers that does not contain chromic acid compounds and is friendly to people and the environment.

●An epoxy resin primer that has excellent adhesion to the propeller surface that rotates at high speed and forms a strong coating, and a newly formulated silicone resin antifouling paint that exhibits excellent antifouling power even during mooring periods. Prevents marine organisms from adhering to the shaft.

●Note: An electric disc sander is required for construction.
Paper discs #80 to 240, nylon discs, etc. can be used, expanding the scope of work.

[Coating amount] Approximately 0.3 square meters (approximately 25 cm diameter propeller)

【set content】
■Nuperacrine PLUS Primer: Main agent x 119g
■Nuperacrine PLUS Primer: Hardening agent x 21g
■Nuperacrine PLUS Primer: Adhesion enhancer ×7g
■Nuperakurin PLUS finish: 80g
■Brush: 1

【how to use】
1.Remove marine organisms and oil from the propeller.
2.Remove the old paint film and polish the propeller surface using an electric disc sander.
3. Wipe with thinner. (Sea Jet Thinner A, Sea Jet Thinner D, etc.)
4. Apply two coats of Nuperacrine PLUS Primer. (Please complete 2 coats within 90 minutes)
5.After the primer dries, apply Nuperacrine PLUS finish. (Recommended 2 coats or thicker coat)
6. After drying thoroughly, lower the rack. (Over 8 hours at a temperature of 20 degrees)
*For details, please refer to the installation instructions included with the product and the Chugoku Paint Co., Ltd. website.

●Type approval number No. 745
-Can be installed on flat water vessels
●Surface is polyester vinyl chloride waterproof cloth (flame retardant)
●The buoyant body is made of closed polyethylene foam. Normally you can put it on a cushion, but in an emergency, grab it with both hands and jump in.
■Buoyancy: 9.3kg
■Size: 400×400×60mm

[Product Specifications]
■Ideal for carrying spare fuel! Since it is a plastic tank, there is no need to worry about rust, and it is lightweight and easy to carry.

■The included nozzle has an air intake vent, allowing you to pour fuel smoothly.

■Size: Approx. 265 x 250 x 135 mm
■Aperture: Φ40mm
■Material: HDPE (high density polyethylene)
Capacity: 5 liters

*The product is a hazardous materials transport container that complies with international recommendations (UN standards) regarding the international transportation of hazardous materials.
*Although this product is UN certified, it may not be possible to fill it up at gas stations, including self-service stations.
*This product cannot be refueled and transported in a passenger vehicle for the purpose of using it as automobile fuel. (*1)
*This product cannot be used for refueling for storage purposes (*2).

(*1) Notification prescribing details of technical standards for the control of dangerous goods (Article 68-4), Regulations on the Control of Hazardous Materials (Article 43-2)
(*2) Fueling for storage purposes refers to fueling for stockpiling. This does not apply if the purpose is to use it immediately. There is no clear definition of the time between refueling and use.

●It is sized to fit a 500ml plastic bottle.
●Since it is easy to install and remove, it is perfect for cases where the base cannot be fixed with screws, such as cooler boxes or shared boats.

Inner diameter: approx. 71mm
Material: resin
-Includes 2 screws for insert parts

sucker base
Size: Height 75 x Width 70 x Depth 60mm
Material: resin
Weight: 60g
Load capacity: 6kg (according to manufacturer)
*Depending on the object to be installed and the usage environment, it may not be possible to adsorb it sufficiently.
*The load value is the hanging load capacity value on a smooth acrylic board. (according to manufacturer research)
This is not the load value including vibration and impact.

●You can hang garbage bags, pliers, etc.
●Since it is easy to install and remove, it is perfect for cases where the base cannot be fixed with screws, such as cooler boxes or shared boats.

Size: Height 46 x Width 28 x Depth 48mm
Material: resin
Hook load capacity: 5kg (according to manufacturer)

sucker base
Size: Height 75 x Width 70 x Depth 60mm
Material: resin
Weight: 60g
Load capacity: 6kg (according to manufacturer)
*Depending on the object to be installed and the usage environment, it may not be possible to adsorb it sufficiently.
*The load value is the hanging load capacity value on a smooth acrylic board. (according to manufacturer research)
This is not the load value including vibration and impact.

●The height of the holder can be adjusted according to the rod.
●There is a notch on the back for triggering the bait reel.
●Since it is easy to install and remove, it is perfect for cases where the base cannot be fixed with screws, such as cooler boxes or shared boats.

Size: Approximately L240 x Φ40mm *Protrusions are not included.
Inner diameter: 35mm
Outer diameter: 40mm
Material: resin

sucker base
Size: Height 75 x Width 70 x Depth 60mm (lever up) / Depth 29mm (lever down)
Material: resin
Weight: 60g
Load capacity: 6kg (according to manufacturer)
*Depending on the object to be installed and the usage environment, it may not be possible to adsorb it sufficiently.
*The load value is the hanging load capacity value on a smooth acrylic board. (according to manufacturer research)
This is not the load value including vibration and impact.

●The height of the holder can be adjusted according to the rod.
●There is a notch on the back for triggering the bait reel.
●Since it is easy to install and remove, it is perfect for cases where the base cannot be fixed with screws, such as cooler boxes or shared boats.

Size: Approximately L305 x Φ50mm *Protrusions are not included.
Inner diameter: 45mm
Outer diameter: 50mm
Material: resin

sucker base
Size: Height 75 x Width 70 x Depth 60mm (lever up) / Depth 29mm (lever down)
Material: resin
Weight: 60g
Load capacity: 6kg (according to manufacturer)
*Depending on the object to be installed and the usage environment, it may not be possible to adsorb it sufficiently.
*The load value is the hanging load capacity value on a smooth acrylic board. (according to manufacturer research)
This is not the load value including vibration and impact.

■Material: Stainless steel

■Size: A total length 304 x B stop hole ~ stop hole 100 x C height 70 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

■Material: Stainless steel

■Size: A total length 254 x B stop hole ~ stop hole 93 x C height 68 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

■Material: Stainless steel

■Size: A total length 203 x B stop hole ~ stop hole 71 x C height 53 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

■Material: Stainless steel

■Size: A total length 152 x B stop hole ~ stop hole 75 x C height 45 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

■Material: Stainless steel

■Size: A total length 126 x B stop hole ~ stop hole 54 x C height 39 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

●Twin wheels with wheel lock

■ Foldable
■ Maximum load: 725kg
■Stroke: 254mm
■Applicable trailer frame width: 76 x 102 mm
■ Wheel size: 178mm x W140 (43x2)
■ Wheel lock included
■Made of aluminum

●The mounting base can be adjusted.

●Please use when mooring to a pier or quay.

●It is recommended to use 4 pieces per boat instead of 2 pieces on each side.

●Split structure so that the fender follows the hull.

●Comes with a rubber stopper and rubber coated hook to allow it to be installed in a variety of locations, and a belt cushion to prevent scratches from rubbing between the fender belt and the hull.

●Size: 10.2x31.8cm

●A stainless steel bracket for fixing navigation lights to pipes, etc.
●You can adjust the angle and install it horizontally even on a sloped wall.

●Bracket for Ibuki Kogyo navigation light “NAUTILIGHT NAVI”
●Adaptation: For 25φ pipe
●Material: Stainless steel SUS316 (main body), SUS304 (attached metal fittings)

【please note】
*Only the bracket is included, and the screws and rubber gaskets that secure the main body and navigation light are not included.

●Stainless steel bracket for fixing navigation lights to pipes, etc.

●Bracket for Ibuki Kogyo's navigation light "NAUTILIGHT NAVI"
●For diameter 25φ pipe
●Material: Stainless steel SUS316 (main body), SUS304 (attached metal fittings)

【please note】
*Only the bracket is included, and the screws and rubber gaskets that secure the main body and navigation light are not included.

●Stainless steel bracket for fixing navigation lights to pipes, etc.

●Bracket for Ibuki Kogyo's navigation light "NAUTILIGHT NAVI"
●Mounting part diameter: 68mm
●For diameter 25φ pipe
●Material: Stainless steel SUS316 (main body), SUS304 (attached metal fittings)

【please note】
*Bracket only; screws and rubber gaskets to secure the main body and navigation light are not included.

●This is a light that is attached to the bow part of a ship. *For ships with a total length of less than 12m

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLB-5AB2

●Type approval number No. 5300

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Advanced technology condensed into a small body!

●Machine-cut heat dissipation plate: A beautiful heat dissipation plate machine-cut from high-strength aluminum and specially treated to efficiently dissipate the heat generated by the LED, achieving an LED unit life of approximately 60,000 hours.

●High light-shielding performance: Based on our unique theory, all parts are placed with high precision to achieve complete light-shielding.

●Wide power supply voltage compatible: The LED unit supports a wide power supply of DC10 to 30V. Built-in stabilization circuit completely absorbs voltage fluctuations.

●Excellent weather resistance and impact resistance: The housing is made of polycarbonate resin. The metal parts are also made of highly weather-resistant materials to ensure high durability and reliability.

●Replaceable LED unit: By replacing the unit at the specified LED time (approximately 60,000 hours), maximum performance can always be achieved.

●Low power consumption: We have succeeded in significantly reducing power consumption by switching to LED. Cut power consumption by up to 90%.

●Installation compatibility: Compatible with conventional Koito products at the same pitch and can be easily replaced.

●GOOD Design GOOD Quality: Winner of the 2013 Good Design Award. made in Japan.

●The size is Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50), the weight is 0.2kg, and the mounting pitch is the same as the old standard Koito Seisakusho type.

*The special packing (product number: 35269) sold separately is a vibration-proof rubber packing that is installed between the boat light and the installation pedestal, etc., and is recommended to be installed to prevent damage to the main unit. The main body has a waterproof structure.

【 specification 】
Manufacturer: Ibuki Kogyo Co., Ltd.
Model: NLST-2Y
Light source: LED
Power supply voltage: DC10V to 30V
Power consumption: 3W
LED unit life: about 60000 hours
Protection grade: IP56
Dimensions: Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50, same as conventional Koito products)
Weight: 0.2kg

[Product specifications]
●12V power can be easily extracted from the cigarette lighter socket and terminal.

●Compatible with taking out electric power! This is a new type of battery BOX whose main terminal has a 60A circuit breaker.

●In accordance with modern needs, it is also equipped with a USB charger socket.

●Equipped with a battery level gauge, so you can conveniently check the remaining battery level with the touch of a button without having to open the lid.

●Socket type: Cigarette lighter (1 burner), USB (2 burners)
●USB socket specifications: Output voltage (DC5V)/Output current (2.1A)
●Built-in breaker: 10A (cigar socket)/60A (main terminal)
●Breaker type: manual reset
●Compatible battery: For 105A or less
-External dimensions: W420 x D230 x H335mm
-Inner dimensions: W340 x D190 x H225mm
(There is a protrusion on the back of the lid to hold the battery in place.)

*If more than the specified current flows, the breaker will operate and shut down the current.
After tripping the breaker, wait a sufficient amount of time before pressing the reset button.