Collection: 新商品

★The Viper paint has been changed to a black paint, and the strap has been changed to a loop. ★

■Material Tower, winch: Made of steel★Black painted
■Winch specifications: single gear
■Load capacity: 540kg
■Accessories: Loop strap, set of mounting bolts

[Information regarding delivery]
・Due to the shape of the product, it cannot be bundled with other products.

■An essential item when mooring your boat! A retractable boat hook that can be fixed in any position.

■Adjusting the length of the handle is very easy, just twist the aluminum pipe part to the desired length, and then twist it the other way.

■Material: Aluminum (body), plastic rubber (handle tip)

■Specifications: 2-stage expansion and contraction

■Stretch width: 124-217cm

■Pipe diameter: 29mm

●Draining water from boats without power sources, such as canoes and rubber boats,
It can also be used to drain water from pools and cages.

●A cordless pump that can be used with seawater or fresh water and uses batteries.

●Since it uses batteries (3 AA batteries), no wiring is required.

●Maximum discharge rate 12.6L/min
●Pumping height: 100cm
● Can be used continuously for about 5 hours (when using alkaline batteries)
●Dimensions: Height approx. 16.2x Diameter approx. 13.3cm
●Weight: Approximately 900g
●Hose length: 1m

[Content capacity] 2L, 5L
[How to use] Put the detergent in a plastic bucket, apply it to the hull with a brush, etc., and wash it with water after 5 to 10 minutes.
[Application] A detergent for removing red rust from iron on FRP ships and dirt at the same time.

【please note】
*As this is an acidic detergent, please be careful not to get it in your eyes or directly on your skin.
*The rust remover may turn yellow, but there is no problem with the ingredients.

●Made by Takeuchi Kasei Co., Ltd.

This is a great value kit that can repair FRP and includes the necessary amount.

[Kit contents]
■Resin: 2kg (with paraffin)
■Hardening agent: 50cc
■Polyester putty: 200g
■Glass mat: 2m x 1m
■Wool roller: 75mm x 1
■ Spatula tree: 1 piece
■Cleaning acetone: 1L
■Polypoid: for 10cc

X-ALL Grease

● Contents: 220g

[Product specifications]
■Material: Stainless steel SUS
■ Breaking strength: 800kg

●A safety hook that is resistant to rust and corrosion.
●The hook has a spring mechanism.

[Product specifications]
■Material: Stainless steel (SUS 304)
■ Breaking strength: 15000kg

●This is the most commonly used round shackle (threaded shackle) made of stainless steel 304 that is resistant to rust and corrosion.

[Product specifications]
■Material: Stainless steel (SUS 304)
■ Breaking strength: 10300kg

●This is the most commonly used round shackle (threaded shackle) made of stainless steel 304 that is resistant to rust and corrosion.

[Product specifications]
■Material: Stainless steel (SUS 304)
■ Breaking strength: 5500kg

●This is the most commonly used round shackle (threaded shackle) made of stainless steel 304 that is resistant to rust and corrosion.

●Drilling size: 24φmm
●Flange size: 51×34mm
●Screw screw hole: φ6mm
- Distance between screw centers: approx. 38mm

*Main body only, mounting screws etc. are not included.

■Specifications: Vinyl coating
■Length: 600mm (excluding hook)
■Hook part thickness: 10-11mm
■Hook length: 110mm
■Wire thickness: 8φ

■Length: 1,170mm (excluding hook)
■Hook: 110mm

●This is a special bag to store when the ball mount is removed.
●Does not make the interior of the car dirty, and you do not have to worry about where to put it.
●Cushion material is sandwiched between the fabrics.

[Disclaimer]
*The ball mount and hitch ball in the image are not included.

[Slant EX type low type round pipe]
A:50Ф B:270mm C:50mm D:19mm

■Material: Stainless steel SUS304

for tight japan

[Slant EX type round pipe]
A:50Ф B:300mm C:110mm D:19mm

■Material: Stainless steel SUS304

For tight japan hitch

[Slant type low type round pipe]
A:50Ф B:175mm C:50mm D:19mm

■Material: Stainless steel SUS304

for tight japan

[Slant type long round pipe]
A:50Ф B:215mm C:150mm D:19mm

■Material: Stainless steel SUS304

for tight japan

[Slant type round pipe]
A:50Ф B:175mm C:110mm D:16mm

■Material: Stainless steel SUS304

for tight japan

■Used when attaching the ball mount to the hitch member.

■Helps prevent the ball mount from falling off and being stolen.

■Since it uses an L-shaped cylinder, it is easy to attach and detach at the center of the hitch member, which tends to be narrow.

■Pin diameter: 16mm

■TIGHT JAPAN, SUNTREX, SOREX, class III compatible

■Ball mount lock key with key

[Square slant type]
Square slant type low type stainless steel 0209-13

A: 50mm x 50mm
B: 210mm
C: 50mm
D: 16mm

for tight japan

[Square slant type]
Slant type low type steel 0209-12

A: 50×50mm
B: 210mm
C: 50mm
D: 16mm

for tight japan

[Square slant type]
Slant type stainless steel 0209-11

A: 50×50mm
B: 210mm
C: 110mm
D: 16mm

for tight japan

[Square slant type]
Slant type steel 0209-10

A: 50×50mm
B: 180mm
C: 50mm
D: 16mm

for tight japan

[Slant Square Type]
Slant type, long type, steel, 0208-18

A: 50 x 50 mm
B: 240mm
C: 150mm
D: 16mm

For Tight Japan

[Square slant type]
Slant type EX steel 0208-17

A: 50×50mm
B: 300mm
C: 110mm
D: 16mm

for tight japan

[Square slant type]
Slant type low type EX steel 0208-16

A: 50×50mm
B: 270mm
C: 50mm
D: 16mm

for tight japan

[Slant EX type round pipe]
A:50Ф B:300mm C:110mm D:19mm

■Material: Steel: Black powder coating

for tight japan

[Slant EX type low type round pipe]
A:50Ф B:270mm C:50mm D:19mm

■Material: Steel: Black powder coating

for tight japan

[Slant type long round pipe]
A:50Ф B:240mm C:150mm D:19mm

■Material: Steel: Black powder coating

for tight japan

[Slant type round pipe]
A:50Ф B:210mm C:110mm D:19mm

■Material: Steel: Black powder coating

for tight japan

[Slant type low type round pipe]
A:50Ф B:175mm C:50mm D:19mm

■Material: Steel: Black powder coating
for tight japan

[Straight round pipe]
A:50Ф B:145mm D:20mm

■Material: Steel: Chrome plated

for tight japan

This is a fitting that is attached to the fuel tank of an outboard motor to take out the fuel.

■Type: Tank side fitting

■Compatibility: For Yamaha outboard motors 1/4”NPT

■Tank part screw size: 1/4 inch diameter 13mm

* Regarding compatibility with YAMAHA outboard motors, even if the outboard motor is compatible, the caliber may be different and it may not be possible to use the product. For fitting compatibility, please check the diameter shape before making your selection.

■This is a fitting attached to the outboard motor fuel tank side hose.

■Can be installed and removed with one touch on the tank side fitting.

■Compatibility: 3/8” hose 8894-7 for Yamaha outboard motors

■Hose compatible size: Compatible with inner diameter 9.5mm hose

*Fix to a hose with an inner diameter of 9.5 mm using a clamp sold separately.

* Regarding compatibility with YAMAHA outboard motors, even if the outboard motor is compatible, the caliber may be different and it may not be possible to use the product. For fitting compatibility, please check the diameter shape before making your selection.

■Material: Stainless steel (SUS304)
■Ball size: 50mm
■Shaft diameter: 25mm

Helps prevent the trailer coupler from falling off.

■Material: Steel
■Pin diameter: mm
■Size: 50x65x65mm (length x width x pin length)

Helps prevent the trailer coupler from falling off.

■Material: Stainless steel
■Pin diameter: 6.0mm
■With strap

[Ordered products]

[Product specifications]
■Hitch ball diameter: 2 inches
■Mounting frame width: 50mm compatible
■Maximum towing weight: Class 2, 1570kg
■Material: Steel Viper color

●It is a strong and stable eye plate because it is firmly fixed at 4 points.

[Product specifications]
■Material: Stainless steel (SUS304)
■Size: Height 50 x Width 40 x Height 29mm

●It is a strong and stable eye plate because it is firmly fixed at 4 points.

[Product specifications]
■Material: Stainless steel (SUS304)
■Size: Length 41 x Width 36 x Height 22mm

[Product specifications]
■Type: Twin
■Material: Stainless steel
■Current: 6A
■Voltage: 12V
■Output: 109dB
■Basic frequency: H490±20/L440±20HZ
■Size: 210×83×55mm

●This is a horn for ships.
●A compact type made of rust-resistant stainless steel material.
●Since it can be installed anywhere, it is ideal for boats with limited space.
●Since it is a twin type with high and low notes, it produces a more spacious tone compared to a single type.

[Product specifications]
■Type: Single
■Current: 3A
■Voltage: 12V
■Output: 106dB
■Basic frequency: 440±20
■Size: 93×83×55mm

●This is a horn for ships.
●A compact type made of rust-resistant stainless steel material.
●Since it can be installed anywhere, it is ideal for boats with limited space.

[Product specifications]
■Type: White
■Material: Plastic
■Flange diameter: 55mm
■Maximum thickness when inserting flange: 31mm
■Total length: 65mm
■Compatible with hose inner diameter 28.5mm

●This is a through hole for discharging the bilge pump overboard.
●Made of plastic
*Sold as one Suruhal Straight. Hoses etc. are not included.

[Product specifications]
■Type: White
■Material: Plastic
■Flange diameter: 39mm
■Maximum thickness when inserting flange: 23mm
■Effective length of hose insertion part: 30mm
■Compatible with hose inner diameter 19mm

●This is a through hole for discharging the bilge pump overboard.
●Made of plastic
*Sold as one Suruhal L-type elbow. Hoses etc. are not included.

[Product specifications]
■Type: White
■Material: Plastic
■Flange diameter: 49mm
■Maximum thickness when inserting flange: 35mm
■Total length: 83mm
■Compatible with hose inner diameter 19mm

●This is a through hole for discharging the bilge pump overboard.
●Made of plastic

*Sold as one Suruhal Straight. Hoses etc. are not included.

[Product specifications]
■Material: Polyethylene
■Total length: approx. 60cm
■Hose diameter: 28.5mm

A freely bendable bellows hose that connects the bilge pump and the Suruhal.
A lightweight corrugated hose that won't collapse even when bent during handling.
It can be easily cut with a cutter.
The parts that can be cut and tightened with hose bands etc. are set every 30 cm.

[Product specifications]
■Material: Polyethylene
■Total length: approx. 60cm
■Hose diameter: 19.0mm

A freely bendable bellows hose that connects the bilge pump and the Suruhal.
A lightweight corrugated hose that won't collapse even when bent during handling.
It can be easily cut with a cutter.
The parts that can be cut and tightened with hose bands etc. are set every 30 cm.

A bracket for navigation lights made of rust-resistant 304 stainless steel.

■Adaptation: Navigation lights made by Koito Manufacturing Co., Ltd.
■Material: Stainless steel (SUS316 lost wax casting, SUS304)
■Mounting surface dimensions: width 107 x height 23/62 degree slope
■Electrolytic polishing finish

【please note】
*Bracket only; screws and rubber gaskets to secure the main body and navigation light are not included.
Rubber gaskets can be purchased separately. (Product number: 35269)