Collection: Best Selling Products

●Genuine TOPS SWITCH SEA-DOO ♯420665951

●Genuine ignition coil for SEA DOO 4 stroke.

*ROTAX 1630 ACE/ROTAX 1500 HO ACE/ROTAX 900 HO ACE cannot be installed.

●SEA-DOO genuine carbon ring kit

●SEA-DOO drive shaft 22mm model

[Compatible models]
SEA-DOO
RXT-X300 (2018~)
GTR230 (2020)

●No drilling or other processing is required as it is bolt-on.

●A spring-retractable reboarding step that enhances playability and is convenient when reboarding from the water.

[Compatibility]
RXT-X300,GTX-L300,WAKE Pro 230,GTX170/155 (2018 or later)

●Convenient for charging mobile phones, wearable cameras, etc.

●This excellent device detects the amount of current required for proper charging time, and prevents devices from overcharging.

●2018 - Standard equipment on GTX Limited300 model.

[Compatibility]
SEADOO SPARK

●A spring-retractable reboarding step that enhances playability and is convenient when reboarding from the water.

[Compatible models]
SEA-DOO SPARK 3-seater

*Ski pylons cannot be used for tubes, etc.

*Cannot be used for SPARK 2-seater.

[Applications] Multi-purpose rust inhibitor for corrosion prevention and rust prevention.
[Contents] 400g

A multi-purpose rust inhibitor that penetrates quickly and prevents rust and corrosion.
Suitable for use in seawater and humid environments.
Highly recommended for maintenance inside the engine after using PWC.

SEADOO genuine product

Spray solvent to clean the outside of the engine.
Used to remove dirt such as grease and oil.

Contents: 400g

●SEA-DOO genuine starter relay STARTER RELAY.

[Compatible models]
SEA-DOO 4-stroke / 2-stroke (580 650 720 800 951 engine)

●This grip has an ergonomic design that allows you to control the machine more easily and aggressively.

●This is a genuine grip adopted by SEA-DOO from 2016.

●Easy to replace the standard grip for Sea-Doo 1999 and later *Excluding '14-'15 SPARK.

[Compatible] Sea-Doo 1999 and later *Excluding '14-'15 SPARK

[Contents] 1 piece on each side *1 piece is required on both sides.

[Installation] Bolts, washers, inserts, and caps are not included, so please use existing ones.

*The first photo is an image of the left and right grips.
*If you need one unit, please order one each for the left and right sides.

●SEA-DOO RXP255/215/GTI155/130 genuine steering cable

●SEA-DOO genuine wear ring 155mm

[Compatible with] SEA-DOO pump diameter 155.5

[Representative model] GTX 4-TEC ('02-'03)/951 model

●SEA-DOO genuine wear ring 161mm

[Compatible with] RXT-X300/RXP-X300/GTX-L300

●SEA-DOO genuine wear ring 159mm

[Compatible with] SEA-DOO 260/255/215

[Application] Deterioration prevention agent added to residual fuel
[Contents] 240ml

●Adding to remaining fuel during long-term storage prevents deterioration.
●Estimated usage: Approximately 1 bottle is used for 76L of fuel.

*Liquid color and packaging are subject to change without notice.
*Since this is a genuine product, we cannot accept returns or exchanges.

■Compatibility: 3/8” hose 8902-7 (17660-ZV5A00) for Honda outboard motors
■Compatible with 9.5mm inner diameter hose

Fitting for outboard motor fuel tank hose
Secures to a 9.5mm inner diameter hose with an optional clamp.
It can be attached and removed with one touch to the tank side fitting.

*The fitting for the outboard motor side is part number: 99522.

■Compatibility: 1/4” NPT 8901-7 (16977-ZV5A00) for Honda outboard motors
■Tank part screw size: 1/4 inch outer diameter 13mm

This is a fitting that is attached to the fuel tank of an outboard motor to take out the fuel.

■Compatibility: For Honda outboard motors (from 2001) 3/8” hose 8900-7 (17650-ZW9-003)
■Compatible with 9.5mm inner diameter hose

By installing this fitting, the connection to the fuel tank can be installed and removed with one touch.
It is used by securing it to a hose with an inner diameter of 9.5 mm using a clamp.

*The fitting for the tank side hose is part number: 99524.

【please note】
Can only be used with square hole type outboard motors.
Please note that some Honda outboard motors manufactured before or around 2001 have round holes instead of the square holes shown.

This is a fitting that is attached to the fuel tank of an outboard motor to take out the fuel.

■Type: Tank side fitting

■Compatibility: For Suzuki outboard motors (75hp or more) 1/4” NPT

■Tank part screw size: 1/4 inch diameter 13mm

* Regarding compatibility with SUZUKI outboard motors, even if the outboard motor is compatible, the caliber may be different and it may not be possible to use it. Please check the caliber size before making your selection regarding fitting compatibility.

■This is a fitting attached to the outboard motor fuel tank side hose.

■Can be installed and removed with one touch on the tank side fitting.

■Type: Hose side fitting (for diameter: Φ13mm)

■Compatibility: For Suzuki outboard motors (75 HP or more) 3/8” hose

■Hose compatible size: Compatible with inner diameter 9.5mm hose

*Fix to a hose with an inner diameter of 9.5 mm using a clamp sold separately.

* Regarding compatibility with SUZUKI outboard motors, even if the outboard motor is compatible, the caliber may be different and it may not be possible to use it. Please check the caliber size before making your selection regarding fitting compatibility.

[Contents] 473ml
[How to use] Spray directly onto the object or soak it into a cloth.
[Applications] Vinyl, rubber products (tires, hoses, rubber, etc.), FRP, plastics, anodized aluminum, etc.
It is effective in preventing deterioration, waterproofing, stain-proofing, mold-proofing, static electricity prevention, and lubrication.

●Ultraviolet deterioration, sun protection agent 303 Aerospace “AEROSPACE=Aerospace” is
This is a protective agent developed to reduce damage to aircraft caused by ultraviolet rays, and is intended for use in situations where ultraviolet rays are much more powerful than on the ground.

●A strong film is formed on the surface to prevent deterioration such as fading, hardening, and cracking caused by ultraviolet rays.
●Effects last for approximately 3 to 5 weeks after one application. With continued use, you can maintain a beautiful luster for many years.

AERO SPACE PROTECTANT Manufactured by Aerospace Protectant

[Contents] 296ml
[How to use] Spray directly onto the object or soak it into a cloth.
[Applications] Vinyl, rubber products (tires, hoses, rubber, etc.), FRP, plastic, anodized aluminum, etc.
[Effects] Effective in preventing deterioration, waterproofing, stain-proofing, mold-proofing, static electricity prevention, and lubrication.

●Ultraviolet deterioration, sun protection agent 303 Aerospace “AEROSPACE=Aerospace” is
This is a protective agent developed to reduce damage to aircraft caused by ultraviolet rays, and is intended for use in situations where ultraviolet rays are much more powerful than on the ground.

●A strong film is formed on the surface to prevent deterioration such as fading, hardening, and cracking caused by ultraviolet rays.
●Effects last for approximately 3 to 5 weeks after one application. With continued use, you can maintain a beautiful luster for many years.

AERO SPACE PROTECTANT Manufactured by Aerospace Protectant

[Product specifications]
■Capacity: 6 gallons / 22.7 liters
■Size: L552 x W375 x H267mm (*Height is up to the cap surface)
■Gauge is included with the main unit

【please note! ]
Since this product does not comply with the Fire Service Act, it cannot be refueled directly from a gas station.
Please use after transferring from a tank that is certified by the Fire Service Act.

*Hose mounting fittings are not included with this tank. Please purchase separately.
The fittings installed on the tank vary depending on the outboard motor manufacturer.

A high-density polyethylene fuel tank for outboard motors.
Since it is made of polyethylene, there is no need to worry about rust and it is resistant to corrosion.

■Capacity: 12 gallons / 45 liters
■Size: Length 575 x Width 355 x Height 330mm

[Information regarding delivery]
・Due to the shape of the product, it cannot be bundled with other products.
・One small parcel is delivered per item, and from the second item onward, shipping fee x (number of items) will be charged.

【please note! ]
Since this product does not comply with the Fire Service Act, it cannot be refueled directly from a gas station.
Please use after transferring from a tank that is certified by the Fire Service Act.

*Hose mounting fittings are not included with this tank. Please purchase separately.
The fittings installed on the tank vary depending on the outboard motor manufacturer.

●Stainless steel bracket for fixing navigation lights to pipes, etc.

●Bracket for Ibuki Kogyo's navigation light "NAUTILIGHT NAVI"
●For diameter 25φ pipe
●Material: Stainless steel SUS316 (main body), SUS304 (attached metal fittings)

【please note】
*Only the bracket is included, and the screws and rubber gaskets that secure the main body and navigation light are not included.

●Stainless steel bracket for fixing navigation lights to pipes, etc.

●Bracket for Ibuki Kogyo's navigation light "NAUTILIGHT NAVI"
●Mounting part diameter: 68mm
●For diameter 25φ pipe
●Material: Stainless steel SUS316 (main body), SUS304 (attached metal fittings)

【please note】
*Bracket only; screws and rubber gaskets to secure the main body and navigation light are not included.

●This is a light that is attached to the bow part of a ship. *For ships with a total length of less than 12m

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLB-5AB2

●Type approval number No. 5300

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Advanced technology condensed into a small body!

●Machine-cut heat dissipation plate: A beautiful heat dissipation plate machine-cut from high-strength aluminum and specially treated to efficiently dissipate the heat generated by the LED, achieving an LED unit life of approximately 60,000 hours.

●High light-shielding performance: Based on our unique theory, all parts are placed with high precision to achieve complete light-shielding.

●Wide power supply voltage compatible: The LED unit supports a wide power supply of DC10 to 30V. Built-in stabilization circuit completely absorbs voltage fluctuations.

●Excellent weather resistance and impact resistance: The housing is made of polycarbonate resin. The metal parts are also made of highly weather-resistant materials to ensure high durability and reliability.

●Replaceable LED unit: By replacing the unit at the specified LED time (approximately 60,000 hours), maximum performance can always be achieved.

●Low power consumption: We have succeeded in significantly reducing power consumption by switching to LED. Cut power consumption by up to 90%.

●Installation compatibility: Compatible with conventional Koito products at the same pitch and can be easily replaced.

●GOOD Design GOOD Quality: Winner of the 2013 Good Design Award. made in Japan.

●The size is Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50), the weight is 0.2kg, and the mounting pitch is the same as the old standard Koito Seisakusho type.

*The special packing (product number: 35269) sold separately is a vibration-proof rubber packing that is installed between the boat light and the installation pedestal, etc., and is recommended to be installed to prevent damage to the main unit. The main body has a waterproof structure.

【 specification 】
Manufacturer: Ibuki Kogyo Co., Ltd.
Model: NLST-2Y
Light source: LED
Power supply voltage: DC10V to 30V
Power consumption: 3W
LED unit life: about 60000 hours
Protection grade: IP56
Dimensions: Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50, same as conventional Koito products)
Weight: 0.2kg

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

-Uses awning fabric that is sturdy and has excellent water repellency
●Size: length 820mm x width 500mm x height 600mm

●Applicable engine size: 175 to 250 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine to select the correct size.

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

●Uses awning fabric that is sturdy and has excellent water repellency.

-Size: length 740mm x width 460mm x height 580mm

●Applicable engine size: 115 to 150 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine.

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

-Uses awning fabric that is sturdy and has excellent water repellency

●Size: length 680mm x width 400mm x height 530mm

●Applicable engine size: 60 to 100 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine to select the correct size.

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

-Uses awning fabric that is sturdy and has excellent water repellency

●Size: length 620mm x width 360mm x height 490mm

●Applicable engine size: 30 to 60 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine to select the correct size.

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

-Uses awning fabric that is sturdy and has excellent water repellency

●Size: length 560mm x width 300mm x height 400mm

●Applicable engine size: 15 to 30 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine to select the correct size.

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

-Uses awning fabric that is sturdy and has excellent water repellency

●Size: length 520mm x width 270mm x height 320mm

●Applicable engine size: 15 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine to select the correct size.

●It is a navigation light that is raised when a ship's operation becomes inconvenient.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLE-4B2

●Type approval number No. 5186

●Light source: light bulb

●Rated voltage: 24V・Rated power: 30W

●Size: Ф90×H109mm

●Made by Koito Seisakusho Co., Ltd.

*Two Class 2 Red Lanterns are required. (Excluding those with a total length of less than 12m) Also, this is a sign that is displayed when operation is inconvenient, and please do not use it for any other purpose.

●It is a navigation light that is raised when a ship's operation becomes inconvenient.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLE-4A2

●Type approval number No. 5185

●Light source: light bulb

●Rated voltage: 12V・Rated power: 30W

●Size: Ф90×H109mm

●Made by Koito Seisakusho Co., Ltd.

*Two Class 2 Red Lanterns are required. (Excluding those with a total length of less than 12m) Also, this is a sign that is displayed when operation is inconvenient, and please do not use it for any other purpose.

●Class 2 tricolor lights and Class 2 white lights apply to sailing vessels less than 12m in total length.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLC-4AB2

●Type approval number No. 5187

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 8W

●Size: Ф111×H282mm

●Made by Koito Seisakusho Co., Ltd.

●This is a light that is attached to the stern (stern) part of a ship.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLS-4AB2

●Type approval number No. 5182

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●This is a light that is attached to the mast of a ship.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLM-4AB4

●Type approval number No. 5181

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●This is a light that is attached to the mast of a ship.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLM-4AB3

●Type approval number No. 5184

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●A navigation light installed on the port side of a ship.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLL-4AB2

●Type approval number No. 5180

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●A navigation light installed on the starboard side of a ship.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLR-4AB2

●Type approval number No. 5179

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●It is a navigation light that must be turned on when the vessel is at anchor.

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Model: MLA-4AB2

●Type approval number No. 5178

●Light source: LED

●Rated voltage: 12V/24V・Rated power: 2W

●Size: Ф90×H61mm

●Made by Koito Seisakusho Co., Ltd.

●Outer diameter: 62mm

●Inner diameter: 22mm

●Bolt: Hole diameter 6mm

●Thickness: 1mm

●The special packing is an anti-vibration rubber packing that is installed between the boat light and the installation pedestal, etc., and is recommended to prevent damage to the main unit.

●Special packing for ship lights (manufactured by Ibuki Kogyo Co., Ltd.) that comply with the new standards.

*Product images are for illustrative purposes only and may differ from the actual product.

[Compatible boat lights] Manufactured by Ibuki Kogyo Co., Ltd.
・Third class mast light Product number: 35262 (Manufacturer product number: NLSM-3W)
・Second class sidelight left red Product number: 35263 (Manufacturer product number: NLSG-2R)
・Second class sidelight right green Product number: 35264 (Manufacturer product number: NLSG-2G)
・Second-class dual-color light Product number: 35265 (Manufacturer product number: NLSW-2B)
・Second class stern light Product number: 35266 (Manufacturer product number: NLSS-2W)
・Second class white light Product number: 35267 (Manufacturer product number: NLSA-2W)
・Second class red light Product number: 35266 (Manufacturer product number: NLSA-2R)

●It is a navigation light that is raised when a ship's operation becomes inconvenient. *For ships with a total length of less than 50m

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Advanced technology condensed into a small body!

●Machine-cut heat dissipation plate: A beautiful heat dissipation plate machine-cut from high-strength aluminum and specially treated to efficiently dissipate the heat generated by the LED, achieving an LED unit life of approximately 60,000 hours.

●High light-shielding performance: Based on our unique theory, all parts are placed with high precision to achieve complete light-shielding.

●Wide power supply voltage compatible: The LED unit supports a wide power supply of DC10 to 30V. Built-in stabilization circuit completely absorbs voltage fluctuations.

●Excellent weather resistance and impact resistance: The housing is made of polycarbonate resin. The metal parts are also made of highly weather-resistant materials to ensure high durability and reliability.

●Replaceable LED unit: By replacing the unit at the specified LED time (approximately 60,000 hours), maximum performance can always be achieved.

●Low power consumption: We have succeeded in significantly reducing power consumption by switching to LED. Cut power consumption by up to 90%.

●Installation compatibility: Compatible with conventional Koito products at the same pitch and can be easily replaced.

●GOOD Design GOOD Quality: Winner of the 2013 Good Design Award. made in Japan.

●The size is Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50), the weight is 0.2kg, and the mounting pitch is the same as the old standard Koito Seisakusho type.

*The special packing (product number: 35269) sold separately is a vibration-proof rubber packing that is installed between the boat light and the installation pedestal, etc., and is recommended to be installed to prevent damage to the main unit. The main body has a waterproof structure.

【 specification 】
Manufacturer: Ibuki Kogyo Co., Ltd.
Model: NLSA-2R
Light source: LED
Power supply voltage: DC10V to 30V
power consumption:
LED unit life: about 60000 hours
Protection grade: IP56
Dimensions: Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50, same as conventional Koito products)
Weight: 0.2kg

●It is a navigation light that must be turned on when the vessel is at anchor. *For ships with a total length of less than 50m

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Advanced technology condensed into a small body!

●Machine-cut heat dissipation plate: A beautiful heat dissipation plate machine-cut from high-strength aluminum and specially treated to efficiently dissipate the heat generated by the LED, achieving an LED unit life of approximately 60,000 hours.

●High light-shielding performance: Based on our unique theory, all parts are placed with high precision to achieve complete light-shielding.

●Wide power supply voltage compatible: The LED unit supports a wide power supply of DC10 to 30V. Built-in stabilization circuit completely absorbs voltage fluctuations.

●Excellent weather resistance and impact resistance: The housing is made of polycarbonate resin. The metal parts are also made of highly weather-resistant materials to ensure high durability and reliability.

●Replaceable LED unit: By replacing the unit at the specified LED time (approximately 60,000 hours), maximum performance can always be achieved.

●Low power consumption: We have succeeded in significantly reducing power consumption by switching to LED. Cut power consumption by up to 90%.

●Installation compatibility: Compatible with conventional Koito products at the same pitch and can be easily replaced.

●GOOD Design GOOD Quality: Winner of the 2013 Good Design Award. made in Japan.

●The size is Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50), the weight is 0.2kg, and the mounting pitch is the same as the old standard Koito Seisakusho type.

*The special packing (product number: 35269) sold separately is a vibration-proof rubber packing that is installed between the boat light and the installation pedestal, etc., and is recommended to be installed to prevent damage to the main unit. The main body has a waterproof structure.

【 specification 】
Manufacturer: Ibuki Kogyo Co., Ltd.
Model: NLSA-2W
Light source: LED
Power supply voltage: DC10V to 30V
power consumption:
LED unit life: about 60000 hours
Protection grade: IP56
Dimensions: Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50, same as conventional Koito products)
Weight: 0.2kg

●This is a light that is attached to the stern (stern) part of a ship. *For ships with a total length of less than 50m

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Advanced technology condensed into a small body!

●Machine-cut heat dissipation plate: A beautiful heat dissipation plate machine-cut from high-strength aluminum and specially treated to efficiently dissipate the heat generated by the LED, achieving an LED unit life of approximately 60,000 hours.

●High light-shielding performance: Based on our unique theory, all parts are placed with high precision to achieve complete light-shielding.

●Wide power supply voltage compatible: The LED unit supports a wide power supply of DC10 to 30V. Built-in stabilization circuit completely absorbs voltage fluctuations.

●Excellent weather resistance and impact resistance: The housing is made of polycarbonate resin. The metal parts are also made of highly weather-resistant materials to ensure high durability and reliability.

●Replaceable LED unit: By replacing the unit at the specified LED time (approximately 60,000 hours), maximum performance can always be achieved.

●Low power consumption: We have succeeded in significantly reducing power consumption by switching to LED. Cut power consumption by up to 90%.

●Installation compatibility: Compatible with conventional Koito products at the same pitch and can be easily replaced.

●GOOD Design GOOD Quality: Winner of the 2013 Good Design Award. made in Japan.

●The size is Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50), the weight is 0.2kg, and the mounting pitch is the same as the old standard Koito Seisakusho type.

*The special packing (product number: 35269) sold separately is a vibration-proof rubber packing that is installed between the boat light and the installation pedestal, etc., and is recommended to be installed to prevent damage to the main unit. The main body has a waterproof structure.

【 specification 】
Manufacturer: Ibuki Kogyo Co., Ltd.
Model: NLSS-2W
Light source: LED
Power supply voltage: DC10V to 30V
power consumption:
LED unit life: about 60000 hours
Protection grade: IP56
Dimensions: Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50, same as conventional Koito products)
Weight: 0.2kg

●This is a light that is attached to the bow part of a ship. *For ships with a total length of less than 12m

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Advanced technology condensed into a small body!

●Machine-cut heat dissipation plate: A beautiful heat dissipation plate machine-cut from high-strength aluminum and specially treated to efficiently dissipate the heat generated by the LED, achieving an LED unit life of approximately 60,000 hours.

●High light-shielding performance: Based on our unique theory, all parts are placed with high precision to achieve complete light-shielding.

●Wide power supply voltage compatible: The LED unit supports a wide power supply of DC10 to 30V. Built-in stabilization circuit completely absorbs voltage fluctuations.

●Excellent weather resistance and impact resistance: The housing is made of polycarbonate resin. The metal parts are also made of highly weather-resistant materials to ensure high durability and reliability.

●Replaceable LED unit: By replacing the unit at the specified LED time (approximately 60,000 hours), maximum performance can always be achieved.

●Low power consumption: We have succeeded in significantly reducing power consumption by switching to LED. Cut power consumption by up to 90%.

●Installation compatibility: Compatible with conventional Koito products at the same pitch and can be easily replaced.

●GOOD Design GOOD Quality: Winner of the 2013 Good Design Award. made in Japan.

●The size is Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50), the weight is 0.2kg, and the mounting pitch is the same as the old standard Koito Seisakusho type.

*The special packing (product number: 35269) sold separately is an anti-vibration rubber packing that is installed between the boat light and the installation pedestal, etc., and is recommended to be installed to prevent damage to the main unit. The main body has a waterproof structure.

【 specification 】
Manufacturer: Ibuki Kogyo Co., Ltd.
Model: NLSW-2B
Light source: LED
Power supply voltage: DC10V to 30V
power consumption:
LED unit life: about 60000 hours
Protection grade: IP56
Dimensions: Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50, same as conventional Koito products)
Weight: 0.2kg