Collection: bestseller

[Product specifications]
■Capacity: 6 gallons / 22.7 liters
■Size: L552 x W375 x H267mm (*Height is up to the cap surface)
■Gauge is included with the main unit

【please note! ]
Since this product does not comply with the Fire Service Act, it cannot be refueled directly from a gas station.
Please use after transferring from a tank that is certified by the Fire Service Act.

*Hose mounting fittings are not included with this tank. Please purchase separately.
The fittings installed on the tank vary depending on the outboard motor manufacturer.

●A foldable, hanging type radar reflector.

[Product specifications]
■Material: Aluminum
■Dimensions: 215 x 215 x 280mm

■Size: Total length 285mm x Ф80mm
■Shaft diameter: 16.0mm

[Product specifications]
■Type: Wall-mounted type
■Body material: Plastic
■Size:
Length 345 x height 65 x depth 33mm
...
■Set of 2

● Gently secure the handle and tip of the rod with foam.
●The soft foam protects the rod from vibrations from the boat and prevents damage to the rod.
●Fix using the hole on the side of the plastic frame.

■Size: Total length 180mm x 80mm
■Shaft diameter: Ф16.0mm

This is a high-strength type hinge that uses stainless steel for the entire wall thickness. *This is not a type that is made thicker by bending a stainless steel plate.
We use SUS316 material that is resistant to rust and corrosion and maintains a beautiful shine.

■Quantity: 1 piece
■Material: Stainless steel (SUS 316)
■Size: 68 x 26 x thickness 4mm

[Product specifications]
■Type: Pipe mounting type
■Material: Stainless steel
■Size: Total length 250mm
■Holder inner diameter: 40φ
■Pipe diameter that can be installed: 19 to 27.2φ (mm)
...
Can be fixed in 360 degrees free position

A rod holder that can be easily attached to a pipe.
Has anti-scratch rubber on the inside of the holder.
The holder part is connected to the pipe fixture with a special metal fitting that can be fixed in any position 360 degrees, so it can be fixed in any convenient position.

●Foldable hanging type radar reflector.

[Product specifications]
■Material: Aluminum
■Dimensions: 300 x 300 x 415mm

The sophisticated aerodynamic design allows for efficient and smooth inflation.
It also has a design that makes it easy to hold with one hand, making it easy to handle.

Can be used with household AC100V or cigarette socket DC12V power supply.
It can inflate approximately 450 liters of air per minute. (Varies depending on temperature, usage conditions, etc.)
A floating ring with a diameter of 60cm can be inflated in about 30 seconds.

Three types of nozzles are included, so just set the nozzle according to the valve size.
It can be inflated smoothly.

■Power supply
1.DC12V (cigarette lighter plug) voltage/current DC12V/12A
2.AC100V (outlet plug) Voltage/Current AC100V/1.8A

■Continuous use time: Approximately 5 minutes (requires cooling for 15 minutes or more after use)
■Air flow rate: Approximately 450L/min *Varies depending on temperature, usage conditions, etc.
■Accessories: 3 types of nozzles, instruction manual (Japanese)

[Caution] It is dangerous to use the product in locations exposed to rain or seawater as it may cause electric shock.

This is a high-strength type hinge that uses stainless steel for the entire wall thickness. *This is not a type that is made thicker by bending a stainless steel plate.
We use SUS316 material that is resistant to rust and corrosion and maintains a beautiful shine.

■Quantity: 1 piece
■Material: Stainless steel (SUS 316)
■Size: 105 x 27 x thickness 4mm

[Product specifications]
■Type: Wall-mounted type
■Material: Stainless steel SUS304
■Size: Height 255 x 48mm
■Holder inner diameter: 40φ
...
■Mounting screws are not included.

There is rubber inside the holder to prevent the rod from being scratched.

Spare cartridge for mini jet horn (product number: 60445).
■Cartridge capacity: 200ml
■Cartridge diameter: approx. 53mm
■Cartridge part overall height: approx. 135mm
■Products not subject to fluorocarbon gas regulations

【please note】
This product does not include a horn.

●Loop strap for Dutton PWC.
●Winch belt with small hook.
- Comes with a loop strap that is convenient for fixing the PWC without damaging it.

[size]
■Strap width: approx. 5cm, length: approx. 3.6m, stitch width: approx. 9.5cm
■Loop part: approx. 2.54cm, length: approx. 1.22m

● Compatible with Hull guard fender, PWC buoy, mark buoy (fender, buoy that uses 97560 nozzle)

●A hand pump for manually inflating air.

●Since the amount of air injected is small, please use it to replenish air when it leaks.

[Set contents] 3-piece set: main body, hose, and nozzle

[Product specifications]
■Material: Stainless steel
■Total length: 2m
■Wire diameter: 8mm
■Chain inner diameter: 38 x 13mm
...
■Accessories: Stainless steel shackle x 2

A stainless steel anchor chain that is rust resistant and has a beautiful luster.

■A manual fuel delivery pump that is convenient when starting an outboard engine.

■Compatible with hose inner diameter 3/8 (9.5mm)

[About the product]
Please note that the product color may differ depending on the arrival time.

●The brass lock (main body: made of brass) prevents theft, making it rust-resistant and durable.

●A set of 5 uses a common key, so you can lock all 5 with one key.

[Product specifications]
■Material: Stainless steel
■Total length: 2m
■Wire diameter: 6mm
■Chain inner diameter: 30 x 10mm
...
■Accessories: Stainless steel shackle x 2

A stainless steel anchor chain that is rust resistant and has a beautiful luster.

[Product specifications]
■Maximum capacity: 300Amp
■Flange diameter: 58.5mm
■With waterproof cap
*Detailed size is shown in the photo

●A simple toggle switch type battery switch.
●Can be used to supply and cut off battery power.
●The red switch lever can be removed.

●This is a spare horn for mini jet horn (product number: 60445).

●It's safe to have one as a spare in case you lose or damage the horn part.

●This is an air horn that makes a loud sound of about 108 decibels just by pressing it.

-A set of 1 bugle part and 2 cartridges. We also sell cartridges only (product number: 60446, ¥1,785), so they can be used repeatedly.

●Cartridge capacity: 200ml/1 bottle

●Intermittent pronunciation time: Approximately 20 minutes
*Intermittent sounding time is the total time it takes for the cartridge to empty after the sound is played several times. Please use this as a guideline as it will vary depending on usage conditions such as external temperature.

*The continuous sounding time is approximately 1/4 of the intermittent sounding time. This is because the temperature inside the cartridge decreases due to sound production, and once the cartridge returns to room temperature, it can be used again.

●The continuous sound time is approximately 1/4 of the intermittent sound time. This is because the temperature inside the cartridge decreases when the cartridge is sounded, and when the cartridge returns to room temperature, it can be used again.

●Products not subject to fluorocarbon gas regulations

●Sound pressure: Approximately 108 decibels

●Basic frequency: 500Hz(+-)30

●Cartridge diameter: approx. 53mm

-Cartridge part overall height: approx. 135mm

●Horn diameter: approx. 60mm

-Horn part total length: approx. 150mm

■Slide width (A): 126.0mm
■Inner width (B): 306.0mm
■Depth (C): 163.0mm

[Product specifications]
■Material: Stainless steel
■Total length: 2m
■Wire diameter: 11mm
■Chain inner diameter: 43 x 14mm
...
■Accessories: Stainless steel shackle x 2

A stainless steel anchor chain that is rust resistant and has a beautiful luster.

[Product size]
■Total length (A): 235.0mm
■Shaft diameter (B): 16.0mm
■Recommended roller width (C): 194.0mm
*Accessories: End cap

■Slide width (A): 126.0mm
■Inner width (B): 206.0mm
■Depth (C): 163.0mm

■Slide width (A): 126.0mm
■Inner width (B): 255.0mm
■Depth (C): 163.0mm

■This is a fuel hose that comes with a pump (primer pump) for manually dispensing fuel, which is convenient when starting an outboard engine.

■Used to connect between the fuel tank and engine.

■Total length: 1.9m

■Hose inner diameter: 3/8 (9.5mm)

■Slide width (A): 127.0mm
■Inner width (B): 128.0mm
■Depth (C): 103.0mm

●By attaching it to a trailer, you can easily lift and lower the vessel.
●Uses a urethane agent that is resistant to deterioration and hardening caused by salt and UV rays, and is smooth and resistant to scratches on the boat.

[Product size]
●Roller diameter 77mm
●Total length 69mm
●Center shaft diameter 12.5mm

[Product size]
■Total length (A): 337.0mm
■Shaft diameter (B): 16.0mm
■Recommended roller width (C): 295.0mm
*Accessories: End cap

[Product size]
■Total length (A): 283.0mm
■Shaft diameter (B): 16.0mm
■Recommended roller width (C): 245.0mm
*Accessories: End cap

●By attaching it to a trailer, you can easily lift and lower the vessel.
●Uses a urethane agent that is resistant to deterioration and hardening caused by salt and UV rays, and is smooth and resistant to scratches on the boat.

[Product size]
●Roller diameter 80mm
●Total length 93mm
●Center shaft diameter 12.5mm

[Product size]
■Total length (A): 136.0mm
■Shaft diameter (B): 16.0mm
■Recommended roller width (C): 99.0mm
*Accessories: End cap

Total length 180mm x width 75mm x shaft length 100mm.

[Product specifications]
■Set of 1 each of plus (red) and minus (blue)
■Can be used up to 800 amperes.

[Applicable] The tip of the terminal (the thinnest part of the terminal)
Suitable for φ17.4mm positive type and φ15.8mm negative type.
■Can also be installed on types with bolts attached to the battery terminal.
■For D terminal
*Not available for positive type φ12.7mm and negative type φ11.1mm

A connector that can be connected to and removed from the battery terminal with a single touch.
Lift up the blue or red cap to loosen the terminal.
You can easily remove the wires from the battery. Attaching is the reverse operation.

This is the bracket required to secure the keel roller and attach it to the trailer.

■Slide width (A): 65.0mm
■Inner width (B): 112.0mm
■Depth (C): 103.0mm

■Roller diameter (A): 89.0mm
■Width (B): 194.0mm
■Shaft diameter (C): 16.0mm

■Material: Stainless steel (SUS316)
■Size
Total length 203 x stop hole ~ stop hole 73 x height 38 mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

●Can be fixed by pulling the pin and rotating it 90 degrees.

■Handle rotation diameter: 20cm
■Mounting frame: up to 76.2 x 127mm
■Material: Steel
■Maximum load: 543kg/1200LBS
■Stroke: 250mm
■Wheel diameter: 6" / 152.4mm

■Material: Stainless steel (SUS316)
■Size
Total length 152 x stop hole ~ stop hole 57 x height 31mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

■Mounting frame: up to 76.2 x 127mm
■Material: Steel/galvanized
■Maximum load: 680kg / 1500LBS
■Stroke: 300mm
■Wheel diameter: 6" double / 152.4mm

With this coupler grip, you can securely grip the tip of the trailer.
Even heavy trailers can be lifted without using a jack and can be easily attached to and detached from the hitch.

■Material: Steel plated
*The grip part is narrower type.

【please note】
Coupler handle only.
Other items used in the photo are not included.
Mounting bolts are not included.

■Material: Stainless steel (SUS316)
■Size
Total length 308 x stop hole ~ stop hole 122 x height 68 mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

[Product specifications]
Outer diameter: 203mm
Opening diameter: 152mm
Hole diameter: 159mm

Working by putting your hands inside the double structure,
This is an opening hole for working in areas that are hard to reach.
Apply silicone adhesive, etc., and then install and fix it.

【please note】
*Cannot be installed on the floor where you will step on it.

[Product specifications]
Outer diameter: 146mm
Opening diameter: 101mm
Hole diameter: 114mm

Working by putting your hands inside the double structure,
This is an opening hole for working in areas that are hard to reach.
Apply silicone adhesive, etc., and then install and fix it.

【please note】
*Cannot be installed on the floor where you will step on it.

■Material: Stainless steel (SUS316)
■Size
Total length 124 x stop hole ~ stop hole 54 x height 28 mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

■Material: Stainless steel (SUS316)
■Size
Total length 203 x stop hole ~ stop hole 84 x height 51 mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

■Roller diameter (A): 89.0mm
■Width (B): 295.0mm
■Shaft diameter (C): 16.0mm

It makes it easy to put on and take off with minimal strain.

■Material: Steel plated

【please note】
Coupler handle only.
Other items used in the photo are not included.
Mounting bolts are not included.

[Product specifications]
■Material: Stainless steel (SUS304)
■Size:
Total length: 260mm
Pedestal dimensions: 85x57mm
■Holder inner diameter
⇒With rubber: 40mm
⇒No rubber: 48mm
[Contents] 5-piece set: rod holder, rubber, stop bolt, intermediate pedestal, and pedestal.

A rod holder that rotates 360° and allows you to freely set the vertical angle according to your preference.
Rubber is pasted on the inside of the rod holder, so there is no need to worry about damaging the rod.