Collection: bestseller

[Product size]
■Total length (A): 283.0mm
■Shaft diameter (B): 16.0mm
■Recommended roller width (C): 245.0mm
*Accessories: End cap

●By attaching it to a trailer, you can easily lift and lower the vessel.
●Uses a urethane agent that is resistant to deterioration and hardening caused by salt and UV rays, and is smooth and resistant to scratches on the boat.

[Product size]
●Roller diameter 80mm
●Total length 93mm
●Center shaft diameter 12.5mm

[Product size]
■Total length (A): 136.0mm
■Shaft diameter (B): 16.0mm
■Recommended roller width (C): 99.0mm
*Accessories: End cap

Total length 180mm x width 75mm x shaft length 100mm.

[Product specifications]
■Set of 1 each of plus (red) and minus (blue)
■Can be used up to 800 amperes.

[Applicable] The tip of the terminal (the thinnest part of the terminal)
Suitable for φ17.4mm positive type and φ15.8mm negative type.
■Can also be installed on types with bolts attached to the battery terminal.
■For D terminal
*Not available for positive type φ12.7mm and negative type φ11.1mm

A connector that can be connected to and removed from the battery terminal with a single touch.
Lift up the blue or red cap to loosen the terminal.
You can easily remove the wires from the battery. Attaching is the reverse operation.

This is the bracket required to secure the keel roller and attach it to the trailer.

■Slide width (A): 65.0mm
■Inner width (B): 112.0mm
■Depth (C): 103.0mm

■Roller diameter (A): 89.0mm
■Width (B): 194.0mm
■Shaft diameter (C): 16.0mm

■Material: Stainless steel (SUS316)
■Size
Total length 203 x stop hole ~ stop hole 73 x height 38 mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

●Can be fixed by pulling the pin and rotating it 90 degrees.

■Handle rotation diameter: 20cm
■Mounting frame: up to 76.2 x 127mm
■Material: Steel
■Maximum load: 543kg/1200LBS
■Stroke: 250mm
■Wheel diameter: 6" / 152.4mm

■Material: Stainless steel (SUS316)
■Size
Total length 152 x stop hole ~ stop hole 57 x height 31mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

■Mounting frame: up to 76.2 x 127mm
■Material: Steel/galvanized
■Maximum load: 680kg / 1500LBS
■Stroke: 300mm
■Wheel diameter: 6" double / 152.4mm

With this coupler grip, you can securely grip the tip of the trailer.
Even heavy trailers can be lifted without using a jack and can be easily attached to and detached from the hitch.

■Material: Steel plated
*The grip part is narrower type.

【please note】
Coupler handle only.
Other items used in the photo are not included.
Mounting bolts are not included.

■Material: Stainless steel (SUS316)
■Size
Total length 308 x stop hole ~ stop hole 122 x height 68 mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

[Product specifications]
Outer diameter: 203mm
Opening diameter: 152mm
Hole diameter: 159mm

Working by putting your hands inside the double structure,
This is an opening hole for working in areas that are hard to reach.
Apply silicone adhesive, etc., and then install and fix it.

【please note】
*Cannot be installed on the floor where you will step on it.

[Product specifications]
Outer diameter: 146mm
Opening diameter: 101mm
Hole diameter: 114mm

Working by putting your hands inside the double structure,
This is an opening hole for working in areas that are hard to reach.
Apply silicone adhesive, etc., and then install and fix it.

【please note】
*Cannot be installed on the floor where you will step on it.

■Material: Stainless steel (SUS316)
■Size
Total length 124 x stop hole ~ stop hole 54 x height 28 mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

■Material: Stainless steel (SUS316)
■Size
Total length 203 x stop hole ~ stop hole 84 x height 51 mm

●This cleat is ideal for areas that require 4-point fixation and strength.
●Uses stainless steel SUS316, which is resistant to rust and corrosion (SUS316 = more corrosion resistant than SUS304).

■Roller diameter (A): 89.0mm
■Width (B): 295.0mm
■Shaft diameter (C): 16.0mm

It makes it easy to put on and take off with minimal strain.

■Material: Steel plated

【please note】
Coupler handle only.
Other items used in the photo are not included.
Mounting bolts are not included.

[Product specifications]
■Material: Stainless steel (SUS304)
■Size:
Total length: 260mm
Pedestal dimensions: 85x57mm
■Holder inner diameter
⇒With rubber: 40mm
⇒No rubber: 48mm
[Contents] 5-piece set: rod holder, rubber, stop bolt, intermediate pedestal, and pedestal.

A rod holder that rotates 360° and allows you to freely set the vertical angle according to your preference.
Rubber is pasted on the inside of the rod holder, so there is no need to worry about damaging the rod.

[Product specifications]
■Material (float): PVC foam
■Float body (per piece)
Size: 141φ×175mm
Hole diameter: 25φ
...

■Rope
Size: 12φ×2m

[Float x 3] + [Rope]
●This is a fender that uses egg-shaped vinyl chloride foam in three rows.
●Float body material: PVC foam

A rope specifically designed for towing such as water toy tubes.

■Suitable for approximately 1 to 2 people
■Length 18m
■ Breaking strength: 1,078kg (2,375lbs)

A compact, classic donut-shaped towing tube.

■Size: 137cm
■Maximum capacity: 1 person ■1 towing point ■PVC tube & nylon full cover

*Pump and rope are not included.

[JSPTOKAI original square clear bag]
56L large capacity bag that can store 4 life jackets at once
The top can be opened wide with a U-shaped zipper to store marine gear.
The bottom is made of mesh material that allows water to drain.
With this bag, you can solve the problem of carrying and storing goods!
■Size: 50x45x25cm
■Fabric: Clear PVC black mesh

[Product specifications]
■Material: Nylon ■Rope diameter: 1/2 (12.7mm)
■Length: 200ft (60m), 300ft (90m)

An easy-to-handle nylon triple rope with excellent abrasion resistance, strength, and flexibility.

[Contents] 2L
[How to use] For removing red rust, blue rust on the hull, removing stains from the wood of the deck, and cleaning light oily substances.

It does not cause corrosion damage to painted surfaces or metal surfaces of the hull, and the luster of the hull does not disappear.

▼How to use▼
Wet the area to be cleaned with water before use.
For normal use, dilute it 3 times and adjust the concentration depending on the degree of dirt.
Using rubber gloves, thoroughly soak a brush, sponge, or cloth in detergent and scrub depending on the degree of dirt.
Be sure to rinse thoroughly with plenty of tap water within 2 minutes to ensure that no Hytrail ingredients remain.
Wipe off moisture with a dry cloth.

*Please try it in an inconspicuous place before use.
*Do not leave it on for more than 2 minutes as it may change color.

Notes
・Never use a spray bottle.
・Do not use on glass surfaces such as automobiles or aluminum parts of vehicles.
・Please do not use the product under the blazing sun or when the product is hot, as stains and uneven color may occur and will be difficult to wipe off.
・Please do not use coatings (mirror finishing, etc.) or painted areas as they will peel off.

CASTRO
Castro Fender was born in Spain in the early 1970s by founder Carlos Castro.
Castro is now one of the world's largest manufacturers of buoy fender floats.
Our products are sold in over 70 countries around the world and are widely praised for their outstanding quality and innovative design.

■Size: Diameter/Total length/Eye diameter
A-0HD: 200mm / 270mm / 25mm
A-1HD: 290mm / 370mm / 25mm

●It is a drop-shaped air fender.
●The rope attachment hole is thick and reinforced with ribs, making it extremely durable. ,
●Can also be used as a course buoy if installed upside down.
●You can easily inflate with an air compressor or air gun.

【please note】
*Air injection nozzle not included *Delivered with air removed *As this is an overseas product, specifications may change without notice.

Connect and use with alligator clips.
Because the hose has a large diameter, air can be injected and discharged more smoothly.

【specification】
■Air flow rate: 350L/min
■Voltage: DC12V
■Current: 33Amp
■Maximum pressure: 2.3psi
■Accessories: 2.6m power cord with alligator clip, air hose, 6 types of attachments

●You can inflate everything from large rubber boats to towing tubes, beach balls, and floats.
●By replacing the injection nozzle with the suction port, it can also be used to bleed air from inflated items.
Since most of the air inside the inflatable product can be removed, it can be folded into a small size.
●When using on towing tubes, please use a foot pump or hand pump for finishing.

●Two-way ratchet lock with plastic cover.

●Material:
[Body] Steel
[Cover] Plastic
●Maximum towing load: 680kg
●Handle length: 23Cm
●Strap size: Width 2" (approx. 5.08cm) 20FT (approx. 609.6cm)

[Product specifications]
●Voltage: 12V
●Current: 1.6A
-External dimensions: 74 x 64 x height 99mm (dimensions in image)
●Displacement volume 31 liters/min
●Compatible with hose diameter 19.0mm
[Adaptation] Ideal for PWC (personal watercraft) and small boats

●Since it is a completely waterproof submersible pump, it is a convenient product for circulating and draining water while on board or during maintenance.
●When wiring, insert a 4A fuse (*) on the + cord side.
(*Fuse is not included with this product and must be purchased separately)

●Made by Fulton, a leading American trailer parts manufacturer.

■Maximum towing load: 580kg. 1300LBS.
■Drum winding capacity: Supports strap lengths up to 20FT (approximately 6,096mm)
■With 2-way ratchet lock
■Handle length 22cm
■Material: Main body made of steel

*Cannot be used for vertical movement.
*Strap is sold separately.

A coating agent containing fluorine-modified silicone.
For protecting and polishing gel coat surfaces of boats and PWCs!
For reproducing black color and polishing resin moldings and gunwales!

■Construction guideline
Aerosol 420ml, application area: approximately 3 to 5.24 feet 2 bottles for ships, 1 bottle for PWC
■Construction method
1. Remove dirt and debris from the area to be applied with a cleaning agent and dry.
2.Apply Marine Glass Coat and spread it over the entire surface using a cloth such as a microfiber cloth.
3. Let it dry at room temperature for about 3 to 8 hours.

●Marine Glass Coat is a coating agent for ship hulls that contains fluorine-modified silicone.
●By forming a glass-like film on the gel coat or painted surface, it creates a glossy luster, and
The water repellent effect reduces the adhesion of dirt and rust, making subsequent cleaning easier◎
●It cures easily at room temperature, so you can easily apply the coating yourself.
It can be used for FRP, so it can be used not only for boat hulls but also for camper shells etc.

[Product specifications]
●Voltage: 12V
●Current: 3.4A
-External dimensions: 74 x 64 x height 111mm (dimensions in image)
●Drainage volume 50 liters/min
●Compatible with hose diameter 19.0mm
[Adaptation] Ideal for PWC (personal watercraft) and small boats

●Since it is a completely waterproof submersible pump, it is a convenient product for circulating and draining water while on board or during maintenance.
●When wiring, insert a 7.5A fuse (*) on the + cord side.
(*Fuse is not included with this product and must be purchased separately)

●Made by Fulton, a leading American trailer parts manufacturer.

■Maximum towing load: 400kg. 900LBS.
■Drum winding capacity: Supports strap lengths up to 15FT (approximately 4,572mm)
■Handle length 20cm
■Material: Main body made of steel

*Cannot be used for vertical movement.
*Strap is sold separately.

●Type approval number No. 745
-Can be installed on flat water vessels
●Surface is polyester vinyl chloride waterproof cloth (flame retardant)
●The buoyant body is made of closed polyethylene foam. Normally you can put it on a cushion, but in an emergency, grab it with both hands and jump in.
■Buoyancy: 9.3kg
■Size: 400×400×60mm

●It is sized to fit a 500ml plastic bottle.
●Since it is easy to install and remove, it is perfect for cases where the base cannot be fixed with screws, such as cooler boxes or shared boats.

Inner diameter: approx. 71mm
Material: resin
-Includes 2 screws for insert parts

sucker base
Size: Height 75 x Width 70 x Depth 60mm
Material: resin
Weight: 60g
Load capacity: 6kg (according to manufacturer)
*Depending on the object to be installed and the usage environment, it may not be possible to adsorb it sufficiently.
*The load value is the hanging load capacity value on a smooth acrylic board. (according to manufacturer research)
This is not the load value including vibration and impact.

●The height of the holder can be adjusted according to the rod.
●There is a notch on the back for triggering the bait reel.
●Since it is easy to install and remove, it is perfect for cases where the base cannot be fixed with screws, such as cooler boxes or shared boats.

Size: Approximately L305 x Φ50mm *Protrusions are not included.
Inner diameter: 45mm
Outer diameter: 50mm
Material: resin

sucker base
Size: Height 75 x Width 70 x Depth 60mm (lever up) / Depth 29mm (lever down)
Material: resin
Weight: 60g
Load capacity: 6kg (according to manufacturer)
*Depending on the object to be installed and the usage environment, it may not be possible to adsorb it sufficiently.
*The load value is the hanging load capacity value on a smooth acrylic board. (according to manufacturer research)
This is not the load value including vibration and impact.

■Material: Stainless steel

■Size: A total length 304 x B stop hole ~ stop hole 100 x C height 70 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

●The height of the holder can be adjusted according to the rod.
●There is a notch on the back for triggering the bait reel.
●Since it is easy to install and remove, it is perfect for cases where the base cannot be fixed with screws, such as cooler boxes or shared boats.

Size: Approximately L240 x Φ40mm *Protrusions are not included.
Inner diameter: 35mm
Outer diameter: 40mm
Material: resin

sucker base
Size: Height 75 x Width 70 x Depth 60mm (lever up) / Depth 29mm (lever down)
Material: resin
Weight: 60g
Load capacity: 6kg (according to manufacturer)
*Depending on the object to be installed and the usage environment, it may not be possible to adsorb it sufficiently.
*The load value is the hanging load capacity value on a smooth acrylic board. (according to manufacturer research)
This is not the load value including vibration and impact.

■Material: Stainless steel

■Size: A total length 152 x B stop hole ~ stop hole 75 x C height 45 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

●You can hang garbage bags, pliers, etc.
●Since it is easy to install and remove, it is perfect for cases where the base cannot be fixed with screws, such as cooler boxes or shared boats.

Size: Height 46 x Width 28 x Depth 48mm
Material: resin
Hook load capacity: 5kg (according to manufacturer)

sucker base
Size: Height 75 x Width 70 x Depth 60mm
Material: resin
Weight: 60g
Load capacity: 6kg (according to manufacturer)
*Depending on the object to be installed and the usage environment, it may not be possible to adsorb it sufficiently.
*The load value is the hanging load capacity value on a smooth acrylic board. (according to manufacturer research)
This is not the load value including vibration and impact.

●A stainless steel bracket for fixing navigation lights to pipes, etc.
●You can adjust the angle and install it horizontally even on a sloped wall.

●Bracket for Ibuki Kogyo navigation light “NAUTILIGHT NAVI”
●Adaptation: For 25φ pipe
●Material: Stainless steel SUS316 (main body), SUS304 (attached metal fittings)

【please note】
*Only the bracket is included, and the screws and rubber gaskets that secure the main body and navigation light are not included.

●Stainless steel bracket for fixing navigation lights to pipes, etc.

●Bracket for Ibuki Kogyo's navigation light "NAUTILIGHT NAVI"
●For diameter 25φ pipe
●Material: Stainless steel SUS316 (main body), SUS304 (attached metal fittings)

【please note】
*Only the bracket is included, and the screws and rubber gaskets that secure the main body and navigation light are not included.

■Material: Stainless steel

■Size: A total length 254 x B stop hole ~ stop hole 93 x C height 68 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

■Material: Stainless steel

■Size: A total length 203 x B stop hole ~ stop hole 71 x C height 53 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

●Press the start switch for 2 to 4 seconds to automatically start suction and drainage, and when drainage is complete, the motor will automatically stop, so there is no need to worry about dry running.

●Voltage: 24V

■Material: Stainless steel

■Size: A total length 126 x B stop hole ~ stop hole 54 x C height 39 mm

■A cleat with 4-point fixation, ideal for areas that require strength.

■Made of stainless steel that resists rust and corrosion

●This is a product that complies with the new standards for ship lights installed on new/existing ships after January 1, 2014.

●Advanced technology condensed into a small body!

●Machine-cut heat dissipation plate: A beautiful heat dissipation plate machine-cut from high-strength aluminum and specially treated to efficiently dissipate the heat generated by the LED, achieving an LED unit life of approximately 60,000 hours.

●High light-shielding performance: Based on our unique theory, all parts are placed with high precision to achieve complete light-shielding.

●Wide power supply voltage compatible: The LED unit supports a wide power supply of DC10 to 30V. Built-in stabilization circuit completely absorbs voltage fluctuations.

●Excellent weather resistance and impact resistance: The housing is made of polycarbonate resin. The metal parts are also made of highly weather-resistant materials to ensure high durability and reliability.

●Replaceable LED unit: By replacing the unit at the specified LED time (approximately 60,000 hours), maximum performance can always be achieved.

●Low power consumption: We have succeeded in significantly reducing power consumption by switching to LED. Cut power consumption by up to 90%.

●Installation compatibility: Compatible with conventional Koito products at the same pitch and can be easily replaced.

●GOOD Design GOOD Quality: Winner of the 2013 Good Design Award. made in Japan.

●The size is Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50), the weight is 0.2kg, and the mounting pitch is the same as the old standard Koito Seisakusho type.

*The special packing (product number: 35269) sold separately is a vibration-proof rubber packing that is installed between the boat light and the installation pedestal, etc., and is recommended to be installed to prevent damage to the main unit. The main body has a waterproof structure.

【 specification 】
Manufacturer: Ibuki Kogyo Co., Ltd.
Model: NLST-2Y
Light source: LED
Power supply voltage: DC10V to 30V
Power consumption: 3W
LED unit life: about 60000 hours
Protection grade: IP56
Dimensions: Ф68 x H56mm (mounting holes 3-Ф5.5 pitch 50, same as conventional Koito products)
Weight: 0.2kg

●Twin wheels with wheel lock

■ Foldable
■ Maximum load: 725kg
■Stroke: 254mm
■Applicable trailer frame width: 76 x 102 mm
■ Wheel size: 178mm x W140 (43x2)
■ Wheel lock included
■Made of aluminum

●The mounting base can be adjusted.

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

-Uses awning fabric that is sturdy and has excellent water repellency
●Size: length 820mm x width 500mm x height 600mm

●Applicable engine size: 175 to 250 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine to select the correct size.

An outboard motor cover is an important item that protects your outboard motor from rain, wind, spray, snow damage, dust, etc.
Like the awning, it is made of a sturdy UV- and waterproof-treated sheet, so you can safely store it for long periods of time.
The lining is made of moquette fabric with a soft pile texture, so the engine head will not be damaged.
It is possible to avoid and cover wiring and piping such as pipes and cables.
Tighten the bottom with a rope to prevent the wind from blowing away.

-Uses awning fabric that is sturdy and has excellent water repellency

●Size: length 620mm x width 360mm x height 490mm

●Applicable engine size: 30 to 60 HP or less

*The above compatible engine sizes are for reference only. Depending on the outboard motor, it may not be possible to use it even if the engine size is within the compatible engine size. Before purchasing an outboard motor cover, please be sure to measure the length, width, and height of your engine to select the correct size.