Collection: bestseller

【size】
■When wound: 90×290mm
■When unfolded: 250x290mm

Protects the hull of your boat from scratches from ratchets and belts.
This large type can easily accommodate large reinforced type ratchets.
Made of the same material as a wetsuit, it is soft and stretchy to fit and cover the hull.
It is convenient because it can be attached after the belt is set on the cargo.
Compared to the type that you put through your belt in advance, it is much easier to use and is recommended.

■Quantity: 1 piece ■Material (main body): Made of chloroprene ■Installation method: Velcro specification

[Disclaimer]
Due to the patterned design, the design, color, and logo size of each product will vary.
Please note that we cannot accept exchanges or returns unless the product is defective.

Trailer parts Boat trailer lashing belt Wet fabric

This is a rear seat cover from the Unlimited "LOGO" series.
To install, simply hang it on the rear seat top.
It is made of chloroprene, the same material used in wetsuits, so even if the surface gets wet, water will not soak through to the back. It is a great item to have when you go out for outdoor activities such as marine sports or camping, or when you go out with children or pets.
The seat won't get wet even if you ride in a wetsuit.
The underside is made of skin material, so it's not only waterproof but also stays in place even if you get in a hurry.

It is also very convenient because if you hang it from the trunk space side, it can be used as a dirt-proof cover for the back space.
It can be rolled up and stored, so it can also be used as a cylindrical cushion or pillow.
It can also be used as a dirt-proof cover for trunks, a flat sheet for outdoors, or a cold weather sheet. The fabric is not too thick.

This product will protect your car's seats from not only marine wear but also sweat, dirt, and wear and tear caused by pets after various field sports.

■ Surface: Chloroprene ■ Back: Slice Skin ■ Size: W125 x H130cm

*Because the material is stretchy, there may be an error of about ±1 to 2 cm during the manufacturing process.
*The image of all seats being occupied is for illustrative purposes only.

[How to care for neoprene fabric products]
- As this is a delicate fabric, do not use a washing machine, dryer or bleach.
-If you need to wash it, we recommend hand washing with fresh water or neoprene detergent.
-There may be creases when you open the product, but this does not mean the product is defective.

[Compatible models] KAWASAKI
STX160 series
ULTRA series
STX series

[Material] Stainless steel polished

【size】
Mounting hole pitch: Approx. 44mm Thread part: M8x28mm
Hook part: Width 136mm x 34mm x 48mm
Weight: Approx. 351g

Luxurious stainless steel buff mirror finish!
The visuals will be upgraded by replacing the cheap genuine hooks with polished ones!

■Capacity: 500ml
■Size Diameter: 73×189mm
Body weight: Approx. 83g
Caliber: approx. 26mm

■Material Body/Hook: Aluminum Cap: Polypropylene/Silicone rubber

New collaboration item with bright red bottle color and double names “UNLIMITED” and “OUTDOOR” now on sale!

Perfect for both the office and outdoors!
It is strong and has no seams because it is molded using pressure from a high-purity aluminum plate.

Stainless steel is heavy and plastic is prone to deterioration.
Aluminum bottles are lightweight and do not deform, covering these weaknesses.
Sports drinks OK! The special stock processing on the inside keeps the taste of your drink.
It also prevents lingering odors, so you can use it without worrying about the last drink you put in it.

■UNLIMITED logo color 2 colors: “black” and “white” (OUTDOOR logo is white only)

*Suitable for ages 6 and up *Please do not add boiling water, dry ice, or carbonated water.
*Other precautions for use are listed on the product box. Please be sure to check before use.

A key chain to prevent small items such as keys from being submerged in water.

The soft foam body also functions as a buoyant body, so it doesn't feel like a foreign body even in your pocket.
Even if it is floating in water for a long time, it is coated with vinyl so it does not absorb water easily.

[Compatible models]
SEA DOO All models

[Material] Polished stainless steel

【size】
Mounting hole pitch: Approx. 44mm Thread part: M8x24mm
Hook part: Width 136mm x 87mm x 40mm
Weight: Approx. 345g

Luxurious stainless steel buff mirror finish!
Replacing the cheap genuine hook will definitely improve your visual appearance!

[Applicable model] KAWASAKI 4-stroke NEWSX-R 1500SXR

A low form style that eliminates design and waste.

This is the lightest design that has succeeded in reducing the weight of the original engine hood by approximately 60%, from approximately 12 kg to 4.8 kg.
Reducing the weight of the engine hood lowers the center of gravity of the hull, leading to improved maneuverability.

[Black gel coat finish]
[Accessories] Food packing

【Guidance】
The angle can be maintained by using the handle pole spring (JI03050) sold separately.

[Compatibility] Kawsaki NEW SX-R 1500SXR
For boats equipped with NewSX-R transform hood (UL46100)

Hood damper kit exclusively for NewSX-R transform hood (UL46100).
Includes a bracket to which a gas damper can be attached.
By wearing it, you can easily open and close the hood and hold it.

[Contents]
Gas damper x 4,
Upper bracket L/R (left/right) x 1 each,
Lower bracket x 1,
Mounting bolts (including washers and nuts) x 4
Spacer x8

[Compatibility]
Kawsaki NEW SX-R 1500SXR

[UL46100 transform hood] and [UL35300 shockless mount] set!

A kit to convert the 1500SX-R to a fixed steering mount like the X-2.
You can enjoy riding like X-2 with SX-R.

All you need is the handlebar and grip.
The included steering mount system uses bearings for smooth steering. The normal condition (handle pole and engine hood) weighs approximately 22 kg, but by replacing it with the transform hood and steering mount, it is possible to reduce the weight by approximately 12 kg, 45%!

It also has excellent expandability, such as the Evolution series,
Steering mount bearing type [UL35211] etc.
Height and bar clamp can be selected by combining optional parts.

[Kit contents]
■Hood body
■Steering mount ASSY
■SUS hinge bracket ASSY
■Lamp cable holder plate
■A set of installation screws
*When installing a fat bar, a separately sold [Part number: UL061 Fat Bar Clamp] is required.

[Compatible with] Standard bar 22.4mm diameter

[Material] Made of aluminum

Clamp for attaching handlebars.
Since the mounting part is flat, it can be used with genuine mounts and UNLIMITED mounts.
When used with Kawasaki genuine handlebar mount, the handlebar will be raised approximately 24mm.

[Compatible models]
KAWASAKI STX160LX

Amplifier stay required when replacing the handlebar mount of STX160LX.
The JETSOUND audio system installed on the STX160LX can be fixed without impairing the operability of the audio amplifier when replacing the steering mount.
This is a stainless steel stay that is compatible with each of the company's steering wheel mounts.

[Compatible mount]
■Product number UL35300 Shockless mount system
■Product number UL35003-ULD ULTRA low down mount kit

Kawasaki 800SX-R

A hood kit that converts the 800SX-R into a fixed steering mount like the 800X-2.

By using this KIT, you will be able to enjoy the ride of the 800X-2 on the SX-R.
The kit's steering position is feedback from the 800X-2's position.
The included steering wheel has bearing specifications and is a 2-way hood that allows you to enjoy smooth steering.

The hood inner is designed to accommodate large chambers. Also,
800SX-R stock handle pole and engine hood weigh approximately 18kg.
Whereas the normal hood/normal handle mount of 800X-2 weighs about 20kg.
The total weight of the kit is approximately 10kg, which is also a 50% weight reduction.

For conversion, all the necessary parts are included in the kit, so all you need to do is prepare the handlebar and grip.

[Kit contents]
■Hood body,
■Steering mount ASSY,
■SUS front bracket,
■Holder (cable) steering [14044-3714],
■Holder (cable) [14044-3757],
■Grommet [92071-3790],
■Plate [13271-3905],
■A set of mounting bolts.
*When installing a fat bar...separately sold (product number: UL061 fat bar clamp) is required.

[Applicable models] KAWASAKI ULTRA300, 310 (-'21) series
*For UNLIMITED shockless mount (UL35300) only

Installed in the throttle case of ULTRA300, 310 (-'21) series
Plate for relocating the cruise control switch. (For UL35300 only)

By using it when replacing the stock throttle lever with an aftermarket part,
There is no need to remove the cruise control function.
■Material: Stainless steel

[Compatibility] Kawsaki NEW SX-R 1500SXR

A conversion kit for NEWSX-R (2017) to a fixed steering mount like the X-2.
By using this kit, you can enjoy riding like the X-2 with the SX-R.

As with the 800SX-R transformation kit, all you need to prepare is the handlebar and grip.
The included steering mount system uses bearings to ensure smooth steering.
The stock SX-R (handle pole and engine hood) weighs approximately 22 kg, but by replacing it with the transform hood and steering mount, it is possible to reduce the weight by approximately 12 kg, 45%!

The height and bar clamp can be selected by combining optional parts such as the Evolution series, which has excellent expandability, and the steering mount bearing type [UL35211].

[Kit contents]
■Hood body,
■Steering mount ASSY,
■SUS hinge bracket ASSY,
■Lamp cable holder plate,
■Installation screw set *For fat bar installation, separately sold [Product number: UL061 Fat bar clamp] is required.

For boats equipped with KAWASAKI 800X-2 lance foam hood

evolution steering system
The UNLIMITED steering mount bearing type can be separated into upper and lower parts, so
Can be used in combination with various UNLIMITED steering mounts.
You can use your favorite version!

[Product number: UL35300] Type combined with shockless mount.

For Kawasaki 800X-2 boats equipped with transform hoods

evolution steering system
The UNLIMITED steering mount bearing type can be separated into upper and lower parts, so
Can be used in combination with various UNLIMITED steering mounts.
You can use your favorite version!

[Product number: UL35003-160] A type that combines a 160mm mount post.

[Compatible models] KAWASAKI ULTRA310LX (-'21) *
*The company's adjustable handle mount
[UL35003] For [UL35003-ULD] (UL35007 head plate only)

A plate to relocate the jet sound amplifier unit installed on ULTRA310LX (-'21).
The handle mount can be replaced.
■Material: Stainless steel

[Compatible models] KAWASAKI ULTRA310LX (-'21) *
*For the company's UL35300 shockless handle mount

A plate to relocate the jet sound amplifier unit installed on ULTRA310LX (-'21).
The handle mount can be replaced.
■Material: Stainless steel

[Compatible models] KAWASAKI ULTRA310LX (-'21) *
*For UNLIMITED UL35003-DAJS, AJS adjustable handle mount series

A plate to relocate the jet sound amplifier unit installed on ULTRA310LX (-'21).
The handle mount can be replaced.
■Material: Stainless steel

[Compatible models] KAWASAKI Kawasaki
For ULTRA310R genuine mount only

A plate to relocate the cruise control switch installed in the throttle case.
Used when replacing the throttle lever on the same model.

■Material: Stainless steel (mirror finish)

[Applicable models] KAWASAKI ULTRA series
ULTRA250X
ULTRA260X/260LX
ULTRA300X/300LX
ULTRA310LX/310LX-S

Clamp standard bar (22.4mm diameter) standard equipment

A dedicated set that allows UNLIMITED handle mount (UL35003) to be used with the ULTRA series!

A 160mm optional mount post is installed to lower it to the limit.
This makes it easier to shift the front load to the riding position when cornering, providing a sense of stability in steering.

[Kit contents]
●UL35003 handle mount kit
(Mount, standard bark clamp, cap bolt M8 x 30 x 30 mm),
●UL35003-160 optional mount post 160mm

For Kawasaki 800X-2 boats equipped with transform hoods

evolution steering system
The UNLIMITED steering mount bearing type can be separated into upper and lower parts, so
Can be used in combination with various UNLIMITED steering mounts.
You can use your favorite version!

[Product number: UL35003-DAJS] Type combined with direct adjustable mount.

Exclusively for UNLIMITED handle mount kit (product number UL35003)

Repair parts base only.
You can adjust the mount to your liking by combining the post, head, etc.

【please note】
This product only includes the base and bolts are not included.

For UNLIMITED adjustable mount (product number: UL35003-AJS)

mount base
■Accessories: Mounting bolts

Exclusively for UNLIMITED handle mount kit (product number UL35003)

Repair parts plate only.
You can adjust the mount to your liking by combining the post, base, etc.

【please note】
This product only includes the plate and bolts are not included.

[Outlet reason] This is a special price for stock replacement.

*This is a new and unused product.
*As this is a special sale item, there may be some stains that do not affect functionality.
*Due to the special price, we cannot accept returns or exchanges.
*We cannot answer any inquiries regarding product specifications or compatibility, as we only have information listed here.

[Compatible models]
For KAWASAKI 1200/1100 KEIHIN CDCV carburetor *We apologize, but we cannot accept inquiries regarding compatibility other than those listed above.

By changing the spring rate, it is possible to change the opening and closing timing of the vacuum valve of the CV carburetor.
●3 types x 1 each ●Spring rate 55, 60, 65

Spare bolt for aluminum lock ring (UL32003) included with UNLIMITED lock grip
*Cannot be used with grips from other manufacturers such as ODI grips.

[Size] M4 x 12mm
[Material] Stainless steel (SUS)

【please note】
*Cannot be used with grips from other manufacturers such as ODI grips.
*Please be careful not to overtorque when tightening.

[Compatible models] YAMAHA
2009~2012 1.8L HO-NA Models・VXR・VXS

Just remove the genuine mesh filter and replace it with this power ring.
Improved airflow provides more power and increases top speed.

Compatible with: 8 holes for MIKUNI

●1 piece
●Weight: 15g
●Adjustable with 8 holes.
●Wire can be drawn from any position.
●The wide adjustment range of the carburetor wire provides uniform acceleration over the entire opening range.

[Applicable models] YAMAHA Yamaha supercharger model *SVHO cannot be installed
GP1800
All FZ / FX SHO Models
2013～ VXR / VXS Models
2013~ FX HO Models

Just remove the genuine mesh filter and replace it with this power ring.
Improved airflow provides more power and increases top speed.

[Applicable models] ULTRA310/300 series

●By installing it on the muffler body, it becomes possible to install sensors such as [Product number: AT-200] auto tune.

●Mounting hole: M18xP1.5mm

[Kit contents] Flange body, blind plug, mounting bolts
*Please use genuine gasket.
*Remove the muffler filter before use.

*About 3 weeks after ordering as it is made to order.

[Compatible models]
Yamaha GP1800/VXR/VXS models from 2011 onwards

■Material (pipe): Aluminum

located between the water vehicle's water box and the hull exit.
Replace your restrictive sound suppression system.
Improves engine performance by reducing back pressure and harmful detonation.
Mandrel-bent aluminum tubing, powder coated to prevent corrosion
A replacement coupler made of high temperature silicone is included.

●Inner diameter Φ50⇔Φ70×Total length 100mm

A silicone coupler with excellent heat resistance, pressure resistance, and oil resistance.
Excellent cost performance and durability.

[Compatible models] Yamaha FX models from 2012 onwards

■Material (pipe): Aluminum

Replaces the restrictive sound suppression system between the water vehicle's water box and the hull exit.
Improves engine performance by reducing back pressure and harmful detonation.
Mandrel-bent aluminum tubing, powder coated to prevent corrosion
A replacement coupler made of high temperature silicone is included.

[Compatible models]
Sea Doo GTI 130 / GTX 170 / GTX 230 / RXT・GTX 300 ALL ('20-)

■Material (pipe): Aluminum

It replaces restrictive sound suppression systems located between the water vehicle's water box and the hull outlet.
It reduces back pressure and harmful detonation, improving engine performance.
Mandrel bent aluminum tubing that is powder coated to prevent corrosion,
Replacement couplers made from high temperature silicone are included.

*For models from 2023 onwards, the Siphon Break Delete Kit ( RS10123-SBD ) is required separately.

●Inner diameter Φ60 ⇔ Φ70×Total length 100mm

A silicone coupler with excellent heat resistance, pressure resistance, and oil resistance.
Excellent cost performance and durability.
Can be used as a joint between 60mm and 70mm diameter pipes.

-Inner diameter Ф147 x total length 85mm

Exhaust coupler with excellent heat resistance, pressure resistance, and oil resistance.
Excellent cost performance and durability.

[Compatible] Fat bar 28.6mm diameter

*22.4mm handlebar (standard) can also be used with handlebar spacer (product number: UL35002)

[Material] Made of aluminum

Clamp for attaching handlebars.
Since the mounting part is flat, it can be used with Kawasaki genuine mount and UNLIMITED mount.
When installed on the Kawasaki genuine handlebar mount, the handlebar mounting position will be increased by 20mm.

[Compatible models] SEA-DOO
GTX-4TEC / RXT / RXT-X(-08)

Luxurious stainless steel buffed mirror finish.
Upgrade your visuals by replacing the cheap genuine hook with a polished one!

[Adaptation] For KAWASAKI 800X-2

[Regarding processing] Styrofoam cutting of the tank is required (*JCI modification application required)
[Note] This product is not subject to complaints as it is a competition part.

Exhaust pipe made by bending aluminum.
Contributes to approximately 50% (grams) lighter weight and lower center of gravity compared to the genuine rubber tube.
Unlike genuine tubes, there is no expansion due to exhaust temperature, reducing trouble.
Carburetor maintenance is more efficient because the pipes are connected to the bottom of the carburetor.
If you use the T-bolt clamp [Product number: JL0250], there is no need to worry about it coming off.
The joint uses a silicone hose that is highly heat resistant, pressure resistant, ozone resistant, and resistant to deterioration.
■Product weight: 1.3kg

【set content】
Pipe body x 1 set
Joint hose Φ60×70mm×2 pieces
Stainless steel clamp x 2

■Correspondence:
KAWASAKI 4 stroke model
SEA-DOO 4 stroke model

■Application: Tool to apply lubrication to the throttle body to prevent it from sticking.

●A must-have item for those riding in seawater!
●Inject lubricant to prevent the throttle body from sticking.

[About installation]
It is necessary to make a hole in the intake pipe using a drill. Install it in front of the genuine throttle body.

【correspondence】
KAWASAKI genuine mount (not compatible with some models)
UNLIMITED MOUNT

Standard handlebar 22.4mm diameter

[Material] Aluminum

This is a clamp to hold the handlebars. The clamp is attached at 60.5 degrees. Handlebars
Looking at the installation position from a 60.5° angle, offset it 25 mm upward and 15 mm forward and backward.

【correspondence】
runabout model
Compatible with 28.6mm handle clamp
*A separate fat bar clamp (UL061 recommended) is required for installation.

■Handle diameter: Clamp mounting part 28.6mm,
■Grip lever mounting part 22.±0.2mm

A wide handle with a thick clamp part and excellent flexibility and strength.

[Application] KAWASAKI 750/800 electrical box [Quantity] Blue 1 piece

By replacing the genuine plastic cap, it becomes an accent of the engine room.
With O-ring

For fat bar (tapered handle) only

■Size: 15cm

[Manufacturer] VOLVO
[Car model] Volvo V90 Cross Country
[Compatible car model] DBA-PB420
[Year] H29.2~
[Compatible grade] T5AWD

[Type] STD
STD: Steel, LTD: Stainless steel, LTD II: Stainless steel

[Traction force] C
[Shape] F-1
[Processing] K-2
[Drilling]-
[Wearing time] 2.5 hours

[About the product]
●All hitch members are made to order. (Estimated delivery time is approximately 10 days to 2 weeks*) *Depends on the vehicle model and material.
●Please note that some materials and types are completely made to order, so cancellations or changes cannot be made after the order has been placed.
●For some car models, we may ask you to fax your vehicle inspection certificate to confirm compatibility.

[Disclaimer]
・Please check compatibility before ordering. Please refrain from checking compatibility after placing your order.
-The photo is an example, and the installation method and shape may vary depending on the vehicle model. Additionally, processing may be required on the towing vehicle side, so please contact us for details.
・As this is a made-to-order product, returns and exchanges are not possible.

[Information regarding delivery]
-Due to the shape of the product, it cannot be bundled with other products.
・Basically, cash on delivery payment is not possible as the product is shipped directly from the manufacturer.

*Shipping cannot be stopped at the shipping company's office *Delivery to corporations/companies and limited to some private residences We cannot accept deliveries in the following cases.
1.A room in an apartment complex
2. Religious corporations, shrines, and temples
3.If it cannot be determined that the building is a corporate building
4.If it is determined that there is a risk of intrusion into the delivery truck.
5. If it is determined that delivery will be hindered due to other special circumstances.

●A separate throttle adapter (product number: UL002-) is required for installation.
*Kawasaki…Only models before 1995 can be installed without an adapter.

The shape of the tip provides a finger feel that enables fine throttle work!
It is an angled type with the lever tilted 4 degrees downward.

You can adjust the length of the wire and the weight of the throttle.
UNLIMITED handlebar mount switch case (product number: UL014/UL015) can also be used.

■Machined aluminum
■Angle type 4°

[Compatible models]
■Kawasaki: 750SX / SXi / SXi-Pro / 800X-2 / SX-R series (800SX-R / 1500SX-R)
■YAMAHA: 700FX / 700SJ

[About processing]
[1] When installing on a YAMAHA boat...If using a genuine YAMAHA lock: Machining of the lock part is required. A genuine KAWASAKI lock was purchased separately, and a genuine part lock assembly [27016-3703] was prepared and assembled.
[2] Use on KAWASAKI boats: Disassemble the genuine lock and assemble it to the product.

[Material] Stainless steel buffed finish

Excellent strength! Will not rust!
Replacing the original one will give the hull a luxurious feel and accent, making it more stylish.
The long hook design helps to securely lock the hood and prevent it from coming off.
The hook part can also be used with YAMAHA locks (processing required for installation)

[Note] Only the latch, internal parts of the lock part are not included.

[Manufacturer] LAND ROVER
[Car model] Discovery
[Compatible car model] LT56A/94A
[Year] H11.6-H17.4
[Compatible grade] XS Plus

[Type] STD
STD: Steel, LTD: Stainless steel, LTD II: Stainless steel

[Traction force] C
[Shape] R-1
[Processing] K-1
[Drilling]-
[Wearing time] 2 hours

[About the product]
●All hitch members are made to order. (Estimated delivery time is approximately 10 days to 2 weeks*) *Depends on the vehicle model and material.
●Please note that some materials and types are completely made to order, so cancellations or changes cannot be made after the order has been placed.
●For some car models, we may ask you to fax the vehicle inspection certificate to confirm compatibility.

[Disclaimer]
・Please check compatibility before ordering. Please refrain from checking compatibility after placing your order.
-The photo is an example, and the installation method and shape may vary depending on the vehicle model. Additionally, processing may be required on the towing vehicle side, so please contact us for details.
・As this is a made-to-order product, returns and exchanges are not possible.

[Information regarding delivery]
-Due to the shape of the product, it cannot be bundled with other products.
・Basically, cash on delivery payment is not possible as the product is shipped directly from the manufacturer.

*Shipping cannot be stopped at the shipping company's office *Delivery to corporations/companies and limited to some private residences We cannot accept deliveries in the following cases.
1.A room in an apartment complex
2. Religious corporations, shrines, and temples
3.If it cannot be determined that the building is a corporate building
4.If it is determined that there is a risk of intrusion into the delivery truck.
5. If it is determined that delivery will be hindered due to other special circumstances.

[Manufacturer] JEEP
[Car model] Grand Cherokee
[Compatible car model] WH47/57
[Year] H17.7-H23.3
[Compatible grades] WH47: Laredo, WH57: OVERAND [Supplement] Notes on processing the inside of the bumper and when installing and removing the bumper

[Type] STD
STD: Steel, LTD: Stainless steel, LTD II: Stainless steel

[Traction force] C
[Shape] R-1
[Processing] D-2/3
[Drilling]-
[Wearing time] 2.5 hours

[About the product]
●All hitch members are made to order. (Estimated delivery time is approximately 10 days to 2 weeks*) *Depends on the vehicle model and material.
●Please note that some materials and types are completely made to order, so cancellations or changes cannot be made after the order has been placed.
●For some car models, we may ask you to fax your vehicle inspection certificate to confirm compatibility.

[Disclaimer]
・Please check compatibility before ordering. Please refrain from checking compatibility after placing your order.
-The photo is an example, and the installation method and shape may vary depending on the vehicle model. Additionally, processing may be required on the towing vehicle side, so please contact us for details.
・As this is a made-to-order product, returns and exchanges are not possible.

[Information regarding delivery]
-Due to the shape of the product, it cannot be bundled with other products.
・Basically, cash on delivery payment is not possible as the product is shipped directly from the manufacturer.

*Shipping cannot be stopped at the shipping company's office *Delivery to corporations/companies and limited to some private residences We cannot accept deliveries in the following cases.
1.A room in an apartment complex
2. Religious corporations, shrines, and temples
3.If it cannot be determined that the building is a corporate building
4.If it is determined that there is a risk of intrusion into the delivery truck.
5. If it is determined that delivery will be hindered due to other special circumstances.