Products selling in the same category

Wire Lubrication TOOL Jet Ski PWC

Vendor:

●When applying lubricant to the throttle or choke wire,
It is very convenient as it allows you to efficiently apply lubricant inside the wire.

[Disclaimer]
*Color may vary depending on shipping time. please note that.

Sale price ¥1,500 Regular price ¥1,500
Regular price ¥1,500
(excluded_tax)

Piston pin puller [Supports piston pins up to 20mm / bore 87mm] 012-152 Special tool

Vendor:

【correspondence】
●Piston pin: up to 20mm
●Bore: up to 87mm

[Application] SPECIAL TOOL for easily removing the piston pin, indispensable during overhaul.

Sale price ¥9,500 Regular price ¥9,500
Regular price ¥9,500
(excluded_tax)
Sold out
cylinder honing 280 tool tool

cylinder honing 280 tool tool

Vendor:

■Applicable: Engines with cylinder bores from 51mm to 177mm
■The roughness of the standard stone is 280.

●Use this honing tool to finish cylinder scratches and ridge reamers when maintaining engines used in automobiles, motorcycles, boats, cultivators, and construction machinery.
●The contact pressure of the honing stone can also be adjusted by adjusting the column.
●The angle of the stone arm can be changed by changing the position of the retaining band to match the cylinder bore.

Sale price ¥3,500 Regular price ¥4,980
Regular price ¥3,500
(excluded_tax)
Sale
Hose clamp pliers wire type 19-757

Hose clamp pliers wire type 19-757

Vendor:

■Body size: 270mm
■Wire total length: approx. 590mm
■Maximum opening width: 42mm
■Weight: 515g

[Application] Tool for removing hose clamps located in hard-to-reach areas where workability is poor.
● Remote control via wire allows work to be done in areas where conventional pliers cannot reach.
●The structure of the pliers allows them to be locked when squeezed.

Sale price ¥7,200 Regular price ¥7,200
Regular price ¥7,200
(excluded_tax)
Sold out

Wire Terminal Tool 19-568 Tool

Vendor:

[Application] For removing male and female terminals of connectors [Blade types] ○4 types, □2 types

Remove the terminal from the connector without causing damage.

Sale price ¥1,200 Regular price ¥1,200
Regular price ¥1,200
(excluded_tax)

Valve spring compressor 19-255

Vendor:

■Material: Carbon steel
■Depth width: 100mm
■Clamping capacity: 0-130mm

A must-have item for 4-stroke maintenance.
Cannot be used if the valve is stuck.
Please use the cylinder head in a stable condition.

[Retainer attachment diameter]
L■Outer diameter 25.4mm Inner diameter 19.0mm
M■Outer diameter 23.2mm Inner diameter 16.0mm
S■Outer diameter 19.2mm Inner diameter 13.5mm

[Included]
Valve attachment x 2 (●short, ●long)

Sale price ¥6,800 Regular price ¥6,800
Regular price ¥6,800
(excluded_tax)

JL191141 Horse Pinsars 2 pieces 19-1141 Tool

Vendor:

The small body makes it convenient for use in narrow spaces.

[Material]
■Body part: Zinc
■Bolt part: Steel
[Size] Approx. 55 x 40 x 13 (mm) ■Clamp size: 20 (φmm)
[Contents] 1 pair (2 pieces)

[Application] Used to stop hose lines.

Sale price ¥1,280 Regular price ¥1,280
Regular price ¥1,280
(excluded_tax)

JL16002S Detente tool Hole diameter Ф2.15

Vendor:

●A tool that allows you to remove the male and female terminals of the connector without damaging them.
●Choose from hole diameter Φ3.2 or Φ2.15.

JL16002S Hole diameter Ф2.15

*Please note that colors may vary depending on the season.

Sale price ¥1,600 Regular price ¥1,600
Regular price ¥1,600
(excluded_tax)

JL006 Silicone tape 19mmx3m

Vendor:

It has excellent water and oil resistance and can be used underwater without using adhesives.

Taking advantage of its excellent insulation properties and excellent flexibility, stretchability, and elasticity,
Perfect fit for any shape.
Highly airtight and highly adhesive, ideal for preventing water leaks, air leaks, and waterproofing.

●High heat and cold resistance operating temperature range (℃): -56 to 260.

Sale price ¥364 Regular price ¥1,600
Regular price ¥364
(excluded_tax)
Sale

[Clearance Sale] Multi-Flywheel Puller ET-7846FP Tools DIY

Vendor:

[Applications] A highly versatile puller that can be used for pulling out steering wheels, flywheels, motorcycle crankcases, gears, etc.

[Usage range] 38-96(mm)

[Tools used] 14mm wrench (*not included)

[set content]
・1 puller body
・1 center screw
・3 center screw adapters
・3/8” (24TPI) x 1-1/2” puller bolts 3 pieces
・3/8” (16TPI) x 2” puller bolts 3 pieces
・3/8” (16TPI) x 3” puller bolts 3 pieces
・2 3/8” (16TPI) x 4-1/2” puller bolts
・2 5/16” (18TPI) x 6” puller bolts
・3 5/16” (18TPI) x 3-1/2” puller bolts
・2 5/16” (24TPI) x 3” puller bolts
・3 5/16” washers
・2 1/4” (28TPI) x 2-1/2” puller bolts
・2 1/4” washers
・M10 (P1.5) x 35mm puller bolt 3 pieces
・3 10mm washers
・M8 (P1.25) x 45mm puller bolt 3 pieces
・M8 (P1.25) x 65mm puller bolt 2 pieces
・M8 (P1.25) x 90mm puller bolt 2 pieces
・3 8mm washers

Sale price ¥4,500 Regular price ¥7,800
Regular price ¥4,500
(excluded_tax)
Sale

[Clearance Sale] Pilot Screwdriver Tool 1060PD ET-1060PD

Vendor:

■Total length: 497mm
●This is a driver exclusively for adjusting the pilot screw of the carburetor.
*Cannot be used for high torque tightening or loosening.

[Set contents] 1 piece each
■Body ■Auxiliary handle
■Bit: +35mm, +58mm, -23mm, -28mm, -35mm, -58mm, -95mm

Sale price ¥5,400 Regular price ¥14,500
Regular price ¥5,400
(excluded_tax)
Sold out

[Clearance Sale] Angle Torque Gauge 985-165 Special Tools Jet Ski 4stroke

Vendor:

[Application] Used for angle tightening during 4-stroke engine assembly.

【how to use】
1. Use a torque wrench to tighten to the specified torque before use.
2. Set the gauge to 0 and fix the main body with an L-shaped arm so that it does not move.
3. Then check the angle indicated by the gauge and tighten to the determined angle.

【detail】
Torque angle socket drive gauge: 1/2 inch
Torque angle readout range gauge: 0-360 degrees
Torque angle gauge reading increment: 2 degrees

Sale price ¥3,990 Regular price ¥5,000
Regular price ¥3,990
(excluded_tax)
Sale
Safety wire twister 84-76006

Safety wire twister 84-76006

Vendor:

[Application] Ideal for locking 2 to wire
An indispensable item for installing seals, grips, etc.

Sale price ¥2,500 Regular price ¥2,500
Regular price ¥2,500
(excluded_tax)

0967 Hose attachment/detachment puller 0967 12-0002 Tool

Vendor:

Press the tip of the puller against the hose and pipe you want to remove,
The hose can be easily removed by squeezing the handle.

■Can be used for pipes with hose size 4 to 13 mm
■Total length: 20cm

Sale price ¥2,000 Regular price ¥2,000
Regular price ¥2,000
(excluded_tax)
Sold out

[Clearance Sale] 0957 Dismantled Piston Compressor

Vendor:

[Reason for outlet sale] Special price to replace inventory.

*This is a new, unused product.
*This is a clearance sale item and may have dirt or other impurities that do not affect its functionality.
*Due to the special price, returns or exchanges are not accepted.
* Regarding product specifications and compatibility, we can only provide information as stated, and we are unable to answer any inquiries.

● Band width: 38mm
●Diameter: Can be used with pistons from 54 to 127 mm.

The band that tightens the ring is a quick release type that can be easily removed and attached by removing the clip.

Sale price ¥2,980 Regular price ¥5,500
Regular price ¥2,980
(excluded_tax)
Sale
floating polyethylene bailer

floating polyethylene bailer

Vendor:

This is the most basic form of limescale pumping.

[Product specifications]
■Material: Made of floating polyethylene
■Size: H85 x W140 x D190mm

【please note】
*Please note that the color may differ from the photo depending on the arrival time.

Sale price ¥750 Regular price ¥750
Regular price ¥750
(excluded_tax)
Pump gauge tester 006-530

Pump gauge tester 006-530

Vendor:

[Application] A tool to measure the pop pressure of the valve seat.

●Used for carburetor setting and tuning.

Sale price ¥10,000 Regular price ¥10,000
Regular price ¥10,000
(excluded_tax)

Flywheel Remover SEA-DOO 003-322 WSM

Vendor:

[Compatible] SEADOO 3 hole 8mm bolt
[Application] Flywheel removal tool

Sale price ¥12,000 Regular price ¥12,000
Regular price ¥12,000
(excluded_tax)

Flywheel puller SEA-DOO for 800/951

Vendor:

[Compatible with] SEADOO 800/951
[Application] Flywheel removal tool

GSX 800(1996-1997)
GSX RFI 800(1999-2000)
GTI LE RFI 800(2003)
GTX 800(1996-1997)
GTX RFI 800(1998-2002)
SPX 800(1997-1999)
XP 800(1995-1997)
GSX LTD 951(1997-1999)
GTX DI 951(2000-2003)
GTX LTD 951(1998-1999)
LRV 951(2000-2001)
LRV-DI 951(2002-2003)
RX 951(2000-2002)
RX-DI 951(2000-2003)
RX-X 951(2001)
XP 951(2000-2002)
XP-DI 951(2003)
XP-LTD 951(1998-1999)
GTX 1503(2002-2006)
GTX-LTD SuperCharged185 1503(2003-2004)
GTX SuperCharged185 1503(2003-2006)
RXP SuperCharged215 1503(2004)

Sale price ¥9,000 Regular price ¥9,000
Regular price ¥9,000
(excluded_tax)

Flywheel Remover KAWASAKI 440-650 Tool 003-319 WSM Jet Ski JETSKI

Vendor:

[Adaptation] KAWASAKI 440-650 engine
[Application] Flywheel removal tool

●3 hole 8mm bolt

【Guidance】
If you are using it on a boat equipped with a 750/800 engine, please purchase "003-317".

Sale price ¥8,500 Regular price ¥8,500
Regular price ¥8,500
(excluded_tax)
Sold out
Recently Viewed Products