High pressure pump High/low pressure automatic switching type electric air pump BM-SP2000V Banana boat Rubber boat SUP

●When applying lubricant to the throttle or choke wire,
It is very convenient as it allows you to efficiently apply lubricant inside the wire.

[Disclaimer]
*Color may vary depending on shipping time. please note that.

【correspondence】
●Piston pin: up to 20mm
●Bore: up to 87mm

[Application] SPECIAL TOOL for easily removing the piston pin, indispensable during overhaul.

■Applicable: Engines with cylinder bores from 51mm to 177mm
■The roughness of the standard stone is 280.

●Use this honing tool to finish cylinder scratches and ridge reamers when maintaining engines used in automobiles, motorcycles, boats, cultivators, and construction machinery.
●The contact pressure of the honing stone can also be adjusted by adjusting the column.
●The angle of the stone arm can be changed by changing the position of the retaining band to match the cylinder bore.

■Body size: 270mm
■Wire total length: approx. 590mm
■Maximum opening width: 42mm
■Weight: 515g

[Application] Tool for removing hose clamps located in hard-to-reach areas where workability is poor.
● Remote control via wire allows work to be done in areas where conventional pliers cannot reach.
●The structure of the pliers allows them to be locked when squeezed.

[Application] For removing male and female terminals of connectors [Blade types] ○4 types, □2 types

Remove the terminal from the connector without causing damage.

■Material: Carbon steel
■Depth width: 100mm
■Clamping capacity: 0-130mm

A must-have item for 4-stroke maintenance.
Cannot be used if the valve is stuck.
Please use the cylinder head in a stable condition.

[Retainer attachment diameter]
L■Outer diameter 25.4mm Inner diameter 19.0mm
M■Outer diameter 23.2mm Inner diameter 16.0mm
S■Outer diameter 19.2mm Inner diameter 13.5mm

[Included]
Valve attachment x 2 (●short, ●long)

The small body makes it convenient for use in narrow spaces.

[Material]
■Body part: Zinc
■Bolt part: Steel
[Size] Approx. 55 x 40 x 13 (mm) ■Clamp size: 20 (φmm)
[Contents] 1 pair (2 pieces)

[Application] Used to stop hose lines.

●A tool that allows you to remove the male and female terminals of the connector without damaging them.
●Choose from hole diameter Φ3.2 or Φ2.15.

JL16002S Hole diameter Ф2.15

*Please note that colors may vary depending on the season.

It has excellent water and oil resistance and can be used underwater without using adhesives.

Taking advantage of its excellent insulation properties and excellent flexibility, stretchability, and elasticity,
Perfect fit for any shape.
Highly airtight and highly adhesive, ideal for preventing water leaks, air leaks, and waterproofing.

●High heat and cold resistance operating temperature range (℃): -56 to 260.

[Applications] A highly versatile puller that can be used for pulling out steering wheels, flywheels, motorcycle crankcases, gears, etc.

[Usage range] 38-96(mm)

[Tools used] 14mm wrench (*not included)

[set content]
・1 puller body
・1 center screw
・3 center screw adapters
・3/8” (24TPI) x 1-1/2” puller bolts 3 pieces
・3/8” (16TPI) x 2” puller bolts 3 pieces
・3/8” (16TPI) x 3” puller bolts 3 pieces
・2 3/8” (16TPI) x 4-1/2” puller bolts
・2 5/16” (18TPI) x 6” puller bolts
・3 5/16” (18TPI) x 3-1/2” puller bolts
・2 5/16” (24TPI) x 3” puller bolts
・3 5/16” washers
・2 1/4” (28TPI) x 2-1/2” puller bolts
・2 1/4” washers
・M10 (P1.5) x 35mm puller bolt 3 pieces
・3 10mm washers
・M8 (P1.25) x 45mm puller bolt 3 pieces
・M8 (P1.25) x 65mm puller bolt 2 pieces
・M8 (P1.25) x 90mm puller bolt 2 pieces
・3 8mm washers

■Total length: 497mm
●This is a driver exclusively for adjusting the pilot screw of the carburetor.
*Cannot be used for high torque tightening or loosening.

[Set contents] 1 piece each
■Body ■Auxiliary handle
■Bit: +35mm, +58mm, -23mm, -28mm, -35mm, -58mm, -95mm

[Application] Used for angle tightening during 4-stroke engine assembly.

【how to use】
1. Use a torque wrench to tighten to the specified torque before use.
2. Set the gauge to 0 and fix the main body with an L-shaped arm so that it does not move.
3. Then check the angle indicated by the gauge and tighten to the determined angle.

【detail】
Torque angle socket drive gauge: 1/2 inch
Torque angle readout range gauge: 0-360 degrees
Torque angle gauge reading increment: 2 degrees

[Application] Ideal for locking 2 to wire
An indispensable item for installing seals, grips, etc.

Press the tip of the puller against the hose and pipe you want to remove,
The hose can be easily removed by squeezing the handle.

■Can be used for pipes with hose size 4 to 13 mm
■Total length: 20cm

[Reason for outlet sale] Special price to replace inventory.

*This is a new, unused product.
*This is a clearance sale item and may have dirt or other impurities that do not affect its functionality.
*Due to the special price, returns or exchanges are not accepted.
* Regarding product specifications and compatibility, we can only provide information as stated, and we are unable to answer any inquiries.

● Band width: 38mm
●Diameter: Can be used with pistons from 54 to 127 mm.

The band that tightens the ring is a quick release type that can be easily removed and attached by removing the clip.

This is the most basic form of limescale pumping.

[Product specifications]
■Material: Made of floating polyethylene
■Size: H85 x W140 x D190mm

【please note】
*Please note that the color may differ from the photo depending on the arrival time.

[Application] A tool to measure the pop pressure of the valve seat.

●Used for carburetor setting and tuning.

[Compatible] SEADOO 3 hole 8mm bolt
[Application] Flywheel removal tool

[Compatible with] SEADOO 800/951
[Application] Flywheel removal tool

GSX 800(1996-1997)
GSX RFI 800(1999-2000)
GTI LE RFI 800(2003)
GTX 800(1996-1997)
GTX RFI 800(1998-2002)
SPX 800(1997-1999)
XP 800(1995-1997)
GSX LTD 951(1997-1999)
GTX DI 951(2000-2003)
GTX LTD 951(1998-1999)
LRV 951(2000-2001)
LRV-DI 951(2002-2003)
RX 951(2000-2002)
RX-DI 951(2000-2003)
RX-X 951(2001)
XP 951(2000-2002)
XP-DI 951(2003)
XP-LTD 951(1998-1999)
GTX 1503(2002-2006)
GTX-LTD SuperCharged185 1503(2003-2004)
GTX SuperCharged185 1503(2003-2006)
RXP SuperCharged215 1503(2004)

[Adaptation] KAWASAKI 440-650 engine
[Application] Flywheel removal tool

●3 hole 8mm bolt

【Guidance】
If you are using it on a boat equipped with a 750/800 engine, please purchase "003-317".