Collection: electrical parts

ON-OFF-ON 3-way rotary switch.
Two electrical components can be operated separately.
It can be used regardless of manufacturer model.
Their high quality and reliability are highly evaluated overseas.
■Produced in Japan

■Completely waterproof
■Cord length: 25cm
■Specifications: 12V 5A

[About installation] Hole drilling (Ф13.5mm) is required on the mounting part.

[Applicable model] KAWASAKI Kawasaki 750/800

A plate that shifts the position of the normal pickup coil and advances the ignition timing (6 degrees).
By shifting the ignition timing, performance is improved throughout the entire rotation range from low to high speeds.
Light tuning starts here!

【correspondence】
KAWASAKI 750/800,
YAMAHA 700/760

[Quantity] 1 piece

This plug cap has a frame made of Bakelite, which has excellent heat resistance and flame retardant properties among synthetic resins, and is covered with silicone.
The plug cord insertion port is a screw-in type, and it will bite into the plug cord securely.

【Product Specifications】
■Material: Silicon coating
■Compatible plug cord: Outer diameter Φ7~8mm
■Internal resistance 5kΩ
■Compatible plug: Separate type/screw type (cannot be used with integrated terminal type)
■Angle 90°

【Guidance】
Recommended for use with the company's product "Reinforced Ignition Coil [Product Number: UL23001]"!

[Compatible models]
KAWASAKI Kawasaki 4st ALL
Compatible plug cord: Φ7~9mm

*Delivery time is approximately 2 weeks after ordering.
[Kit contents]
- 4 types of conductive spiral tubes (approximately 340, 500, 600, 700mm),
-Earth cord 180mm x 4,
●Cord clamp x 4,
-Screw M4-12, nut M4, spacer x 4 each
- Cable ties x 8

Conductive spiral tube with special plating.
By installing it, the spark plug voltage of CDI ignition model will increase by about 20%!
It is possible to boost the discharge voltage of the spark plug by wrapping it around the plug cord and grounding it.

When the engine is running, the plug cord constantly generates noise as a reaction to the flow of electricity.
By organizing the noise (magnetic field), the reaction is reduced and a more powerful spark is created.
It brings absolute effects to everything from normal engines to racing engines.

[Compatible models] KAWASAKI 750/800

[Kit contents]
★Digital CDI power unit (product number: UL21001)
★Lightweight duralumin flywheel (product number: JL-K8P-F)

Digital CDI-R power unit and flywheel kit

Suitable for a wide range of users, including Sunday users, race users, and freestyle users. The engine speeds up smoothly from low rotation to high rotation.
The 800g lightweight flywheel promises quick response and can be expected to increase the high rotation range.

Digitally controls ignition timing using a high-performance 8-bit microcontroller
Built-in different ignition timings for MAP1 to 4. It can be changed with a switch.
Since this is a race-specific model, the limiter has been cut.
It has a compact design that fits neatly into an electrical box, and has unparalleled high durability.
In order to cope with the high engine speed due to the use of a lightweight flywheel, the line has been strengthened to ensure that the input signal from the pickup coil is received.
An ignition map that increases torque characteristics at high rpm to avoid torque loss in the high rpm range when using a lightweight flywheel.

■CDI: Made in Japan

■Compatible models: KAWASAKI 750/800

Digital CDI-R power unit.

Suitable for a wide range of users, including Sunday users, race users, and freestyle users.

Ignition timing is digitally controlled using a high-performance 8-bit microcontroller.
It is possible to switch between different ignition timings for MAP 1 to 4 using the built-in switch.
Since this is a race-specific model, the limiter has been cut.
The input line has been strengthened to accommodate high rotation speeds. In addition, the torque characteristics have been increased to high rotation speeds.
Compact design that fits neatly into the electrical box.
We have achieved unparalleled high durability.
■CDI: Made in Japan

【Guidance】
By using the optional lightweight duralumin flywheel (product number: JL-K8P-F), you can expect even more response and improved high rotation range.
(Set part number: UL21001-KF Total Loss Digital System Kit)

[Applicable models] SEA-DOO T3, S3, GTI hull
*For RULE bilge pump only

[Accessories] 4 rivets

[01689] 500 [97033] 800 [01608] 1100 This is a stay when installing the bilge pump.
A bilge pump can be installed.
Bilge pump holder [12-1116] can be installed.

[Compatible models] YAMAHA 700SJ ('96~)
*For RULE bilge pump only

[Accessories] 8 rivets

[01689]:500[97033]:800[01608]1100 Stay when installing bilge pump.
Two bilge pumps can be installed.
Bilge pump holder [12-1116] can be installed in 45 degree increments.

[Compatible models] KAWASAKI STX-R / Ultra150
[Specifications] Compatible with regular gasoline

This is a purely domestic CDI unit, and we have researched the engine characteristics of STX-R/Ultra150 to achieve the best ignition characteristics.
Easy to install and shortens the time to reach top speed from low speed.

[About installation]
Bolt on.
*Please set according to the engine specifications and driving conditions.

KAWASAKI 4-stroke ALL
STX-12F
STX-15F
ULTRA LX/250X/260X/260LX/300X/300LX

[Product name] LED stop lamp LED STOP LUMP

[Product contents]
●Lamp body
●Connection terminal
●Mounting screw

【Product details】
Light dimensions: 110×30×10mm
Screw hole: 6.5mm
Cord length: 800m

A highly water resistant and durable LED lamp with a flexible lens body.
The compact body allows installation anywhere, and it is very easy to install on curved surfaces using strong adhesive tape.
By lighting up the LED lamp, when touring, etc., you can quickly notify following boats of a slowdown, and can be expected to be effective in preventing rear-end collisions.
You can also notify people around you of your boat's presence from a distance.
Adopts high-brightness LED and boasts high visibility.
A flexible light lens body that can be installed anywhere is ideal for PWC.

[Regarding installation] Please install using the double-sided tape on the back of the lamp body.

[Information] If you are looking for a lamp unit, please use [Product number: JL23011].

ON-OFF-ON 3-way rotary switch.
Two electrical components can be operated separately.
It can be used regardless of manufacturer model.
High quality and reliability are highly evaluated overseas.
■Produced in Japan

■Completely waterproof
■Cord length: 3m
■Specifications: 12V 5A

[About installation] Hole drilling (Ф13.5mm) is required on the mounting part.