Collection: bestseller

【Compatible models】 KAWASAKI

Very convenient, as it floats even if dropped in water.
Please use according to your wrist size.

【Float Color】×【Lanyard Color】
A2126 Black × Silver
A2148 Red × Black
A2151 Blue × Silver
A2149 Green × Black

When used by attaching it to a stabilizer, it improves straight-line performance,
Make control safer and easier.

■Quantity: 1 set of 2 pieces of the same color
■Compatible with: Hydrofoil stabilizer exclusive product
→Large type: Compatible with product number 04824 / 21971
→Small type: Compatible with product number 04826 / 21972

[Applicable] Mikuni carburetor YAMAHA GP1200R/XLT1200/XL-L

You can easily adjust the screw by replacing it.
Easily change carburetor settings.

[Effect]
●The water flow flowing on the surface dynamically creates upward thrust pressure on the bottom surface of the stabilizer, pushing up the stern and pushing down the bow, shortening the time until planing, increasing propeller efficiency, and improving fuel efficiency!
●The water flow created by the propeller is efficiently pushed backwards, improving controllability and straightness.

●The time until planing is halved, making running and control smoother. It also saves fuel consumption by 10-40%.

[Installation method]
1■ Place the stabilizer on the cavitation plate and mark the 4 places to drill holes.
*At that time, after drilling a hole with a diameter of 6 mm, make sure that there is a gap of at least 1 cm between the edge of the cavitation plate and the edges of all four holes.
*If there is no gap of 1cm or more, the cavitation plate cannot be installed as there is a possibility that it will be damaged while driving.

2■ Use a drill to drill holes with a diameter of 6 mm in four locations, and then pass the included bolts from under the cavitation plate.
*From the bottom, temporarily tighten the 4 places by inserting the bolts → cavitation plate → rubber washer → stabilizer → washer → nut.

3■ Perform the final tightening, but instead of final tightening one location at a time, do it diagonally a little at a time, ``evenly in four locations in an X-shaped order.''
4■ Since a locking nut is used, there is no need to tighten the bolts until the stabilizer is deformed.
5■ Move the stabilizer and check that if there is no play, the installation is complete.

【lastly】
Do a test drive and check again to make sure there is no play between the stabilizer and cavitation plate.

[Product specifications]
■Type: Large
■Color: Black / Gray
■Size: Please check the image.
■Correspondence
→Large: 40 to 300 horsepower outboard motor, inboard/outboard motor

A spare/replacement bulb for navigation lights manufactured by Koito Seisakusho Co., Ltd.
JCI certified product Type approval number obtained

■Applications: 4 types of front lights, 2 types of rear lights, 2 types of bicolor lights, 2 types of white lights
01458: 12V10W
01459: 24V10W

[Note] Please select the voltage and wattage before ordering.
●Voltage: 12V/24V
● Wattage: 10W/20W/30W
We have the above lineup. (This product is 10W)
Please select the appropriate product according to your application.

Manufactured by Koito Seisakusho Co., Ltd.

A spare/replacement bulb for navigation lights manufactured by Koito Seisakusho Co., Ltd.
JCI certified product Type approval number obtained

■Application: 01457 → front light three types of light, 01468 & 01469 → red light
01457: 24V20W
01468: 12V30W
01469: 24V30W

[Note] Please select the voltage and wattage before ordering.
●Voltage: 12V/24V
● Wattage: 10W/20W/30W
We have the above lineup. (This product is 20W & 30W)
Please select the appropriate product according to your application.

Manufactured by Koito Seisakusho Co., Ltd.

19-1600: SBN38mm
19-1601: SBN44mm

A set of replacement butterfly and shaft.

A spare/replacement bulb for navigation lights manufactured by Koito Seisakusho Co., Ltd.
JCI certified product Type approval number obtained

■Application: Application: Gendou, tricolor light
01456: 12V20W
26705: 24V20W

[Note] Please select the voltage and wattage before ordering.
●Voltage: 12V/24V
● Wattage: 10W/20W/30W
We have the above lineup. (This product is 20W)
Please select the appropriate product according to your application.

Manufactured by Koito Seisakusho Co., Ltd.

[Product specifications]
■Material:
■Size: Diameter/Length/Eye diameter
G-1: 89mm /330mm / 9mm
G-2: 114mm /406mm / 12mm
G-3: 140mm /508mm / 12mm
G-4: 165mm /584mm /19mm
G-5: 216mm /678mm /19mm
G-6: 257mm /762mm /22mm

●Highly weather resistant standard model that protects your boat from scratches ●Polyform's air fender, G series fender.
●Standard bale-shaped design that perfectly matches any ship.

【please note】
*Since it is a sealed type, it will be delivered with air injected.
*Please note that additional air injection is not possible.
POLYFORM Manufactured by POLYFORM

[Product specifications]
■Type: Recessed type
■Material: Stainless steel
■Total length: 220mm
■Holder inner diameter: 41mm
[Contents] 5-piece set: rod holder, rubber, stop bolt, intermediate pedestal, and pedestal.
...
■With base gasket integrated rubber cap

This is a stainless steel rod holder made by Atwood.
Comes with a UV-resistant cap to prevent water from entering.

Made by ATTWOOD

【Product Specifications】
■New Standard Compliant Model/TYPE: A
■Applicable Weight: 40kg or more. Can be used for children.
■Initial Buoyancy: 7.5kg
■Waist Size: Up to 105cm
■Material: (Body) Polyester, (Buoyancy Material) Oil-resistant foamed polyethylene

This is a fixed-type life vest that boasts absolute safety.
Because it is worn like a vest, it is less likely to come off in the event of falling into the water.
The front closure is zippered.

56017/Total length A: 136.0mm Shaft diameter B: 12.5mm Recommended roller width: 99.0mm
56018/Total length A: 159.0mm Shaft diameter B: 12.5mm Recommended roller width: 127.0mm

[Product specifications]
■Material: Made of reinforced vinyl
■Diameter: Approximately 20cm

●Multi-use float that can be used as a marker buoy or fender.
●This buoy is ideal for setting up courses for water skiing, wakeboarding, personal watercraft, etc.
●Made of marine grade reinforced vinyl, the same as commonly used air fenders,
It is less susceptible to deterioration due to UV rays.

●Three fluorescent colors that are highly visible even on water.
●It is a product that does not easily fade even after long-term use.

【please note】
Air injection nozzle is not included.
*Please purchase the air injection nozzle (product number: 97560) separately.

[Product specifications]

■Size: Diameter/Total length/Eye diameter
F-1: 150mm /640mm /18mm
F-2: 191mm /635mm /22mm
F-3: 208mm/635mm/22mm
F-5: 279mm /762mm /24mm

●Polyform's air fender and F fender are extremely strong fenders.
●The eye part is reinforced with thick rubber, making it extremely durable.
●Can withstand the high pressure of not only small ships but also large ships.

【please note】
Nozzle is not included.
*Please purchase the nozzle (product number: 97561) sold separately.

●10 pieces

●Hose outer diameter:

16mm…for 5/16

18mm…for 3/8

24mm…For primer pump

[Product specifications]
■Size: Diameter / Total length / Hole diameter
HTM-1: 152mm /381mm /16mm
HTM-2: 203mm /508mm /16mm
HTM-3: 254mm /660mm /16mm

●Polyform's air fender, HTM fender.
●Type with a through hole in the center for the rope to pass through. You can hang the fender with a single rope, which is very convenient when installing it horizontally.
●You can also hang it vertically by making a knot after passing the rope through it.

【please note】
Nozzle is not included.
*Please purchase the nozzle (product number: 97561) sold separately.

POLYFORM Manufactured by Polyform

A jacket with a simple and universal design that uses a polyester body liner as the outer material.
The body also has a texture similar to a thin down jacket.

This item shows JETPILOT's attention to detail in detail, such as the left and right front welt pockets with zips and the contrasting design of the hoodie straps.

Although it is simple, it is a useful item as the main outerwear for styling.

■Actual size when laid flat (chest measurement/length)

M size: 120cm/62cm
L size: 125cm/64cm
XL size: 129cm: 67cm

*Please forgive any errors as the measurements are taken by our staff.

This is Annieversary model apparel with the original logo revived.
The brushed lining makes it a little looser, and the fabric isn't too thick, so it's perfect from fall to spring!
Round neck trainers with a simple design are popular among people of all ages.

■Poly/cotton outer body 320gsm fleece brushed lining type

■Actual product size (chest measurement/length)

S: 95cm/70cm
M:100cm/72cm
L:106cm/74cm
XL:116cm/77cm

*Please note that there may be errors due to measurements taken by our staff when placed horizontally.

*American size, one size larger than Japanese size.

[As this is a special price item, we cannot accept returns or exchanges. ]

This is a multi-use waterproof backpack made by Dry Case in the United States.
3 Rolling system with extremely high performance, even in bad weather such as water spray, mud, sea breeze, rain and fog
It firmly protects the clothes and equipment you put inside.

In addition, we use environmentally friendly materials that are resistant to tears and sharpness.
Even if it gets dirty, you can easily remove it by wiping it with a wet cloth.

●Size: 69 x 40 x gusset 18cm (capacity 30L)

The size is large enough to hold bath towels, footwear, and other small items.

Stable shoulder straps and waist belt allow you to use both hands.
It also comes with a sturdy rubber strap, so you can hold it in your hand.
It also has plenty of storage specifications, including a zippered mesh pocket on the front and side pockets on the left and right.
It also provides full support for your back or lower back.

This cloth mask uses 100% cotton for the outer material and 100% quick-drying polyester fabric for the lining.
There is a pocket inside the main body that can be used to insert non-woven fabrics, gauze, etc.

●Masks do not completely prevent infection (virus invasion).
●Non-medical use, non-dust-proof/gas-proof use

【Product Specifications】
■Set of 2 ■Outer fabric: 100% cotton
■Lining fabric: 100% polyester
■Ear hook part: 100% cotton
■Size: L (Men's) W22cm x H15cm (mask part)
*This is the size listed in the catalog and may differ from the actual size.

The optimal cutting pattern, which thoroughly analyzes rider movements based on impressions from exclusive professional riders and has undergone repeated testing, is adopted. This is an ideal wetsuit that effectively uses highly elastic materials. You will surely experience UNLIMITED's highest quality and potential.
The side cutting makes the body shape look clean and has excellent design.

-UNLIMITED RUSH-
Aiming for higher performance, under the supervision of UNLIMITED's exclusive professional riders, the design is focused on specifications that maximize the "power," "speed," and "stability" of PWC. This is the ultimate wear that allows riders to embody smartness that is in line with the times.

【Features】
・Shoulder Velcro
Smooth donning and doffing possible with Velcro on the left shoulder of the long john
・Stabilize Pad
The pad on the knee part helps improve grip during riding
・2.5mm Flex Neoprene
The new material, further evolved from conventional fabrics, offers the highest level of feel and elasticity.
・Ink Pad
Flexible and lightweight, yet pursues improved grip
・Ankle Zipper
Zippered Velcro tape for easy donning and doffing protects the slider

Kawasaki 800SX-R normal (genuine) hood only

Decal kit for 800SX-R normal hood.

It uses 3M full color sheets and has beautiful graphics, as well as
Easy-to-install cut patterns make new visuals easy to install.
This film has a proven track record of maintaining its original beauty over a long period of time due to its highly durable surface treatment.

The colors are standard green and red. Please choose your favorite color.

[Disclaimer]
As this item is made to order, we cannot accept changes or cancellations after the order has been placed.

Boat equipped with Kawasaki New SX-R transform hood (UL46100)

Decal kit for boats equipped with New SX-R Transform Hood (UL46100).

It uses 3M full color sheets and has beautiful graphics, as well as
Easy-to-install cut patterns make new visuals easy to install. This film has a proven track record of maintaining its original beauty over a long period of time due to its highly durable surface treatment.

The colors are standard green and red. Please choose your favorite color.

[Disclaimer]
As this item is made to order, we cannot accept changes or cancellations after the order has been placed.

For ULNIMITED full billet sponsons (UL53200)

aluminum billet

Contents: 4 pieces

[Support] M8 flat head screw

[Quantity] 1 piece
*Usually countersunk screws require counterbore processing on the mating material,
By using rosette washers, you can use countersunk screws without machining.

Be stylish with your favorite color! Also good as a design element!
You can also dress it up by replacing the bolts that secure the sponsons.

[Compatible models]
SEA-DOO 4-stroke ALL model (*excluding SPARK)

*Please use the genuine O-ring when using.

The oil cap can be removed without special tools when changing the oil.
It's very stylish and makes the engine room stand out.

UL53001SL Silver
UL53001OR Orange
UL53001RD Red
UL53001YL Yellow

[Applicable models] SEA-DOO 4-stroke model (excluding SPARK)

Install it on top of the genuine oil cap.
The clutch function that prevents the oil cap from being over-tightened remains the same.
The aluminum billet cap stands out as an accent in the engine room.

[Information] We also recommend using the company's billet oil filter cap (UL53001).

[Compatible models]
KAWASAKI Kawasaki
YAMAHA
SEADOO
*Processing to the hull is required for all models of all manufacturers.
*For models with a vent function (fuel tank pressure punishment valve) on the fuel cap, a separate tank pressure release is required.

Durable billet aluminum finish.

By installing this fuel filler on SEADOO boats and YAMAHA boats,
UNLIMITED billet fuel cap [Product number: UL030, UL036] etc.
Fuel cap for KAWASAKI can now be used.

General purpose
*If used on a model with a vent function (fuel tank pressure relief valve) on the fuel cap, a separate pressure relief must be provided.

Set of machined aluminum fuel cap and filler.
It has a built-in fuel hose that prevents fuel from blowing back.
Double line hose structure.

【 KAWASAKI 】
STX160

●Deck mats for the Kawasaki STX160, newly released by UNLIMITED.
●In addition to excellent cushioning from its two-layer mat structure,
the latest laser processing technology was incorporated in its design,
eliminating surface tension to allow for smooth drainage from the deck,
and creating a durable mat that maintains high grip even when wet.

●The double-sided tape used is not the conventional 3M tape,
but rather a new PSA2 based on 3M 9786, which offers superior wrinkle resistance, durability, and adhesion.

●Includes double-sided tape

【Disclaimer】
Due to the nature of the product's material and color, certain colors (green, orange, red, pink, yellow) may
fade over time and with use.
Please note that fading and discoloration are not covered by warranty.

【Regarding "Backorder/Pre-order" Items】
These items will be custom-produced by the manufacturer.
Please note that changes or cancellations are not possible after ordering for custom-produced items.
Please be aware that backorders typically take about 2 to 2.5 months to process.

KAWASAKI: NEX SX-R (4-stroke)

● Deck mat for Kawasaki NEX SX-R (4-stroke), newly released by UNLIMITED.

● In addition to excellent cushioning from its two-layer mat structure,
it features a design incorporating the latest laser processing technology.
This not only eliminates the surface tension of water, allowing for smooth drainage from the deck,
but also creates a durable mat with high grip even when wet.

● The double-sided tape used is not the conventional 3M tape,
but PSA2, newly developed based on 3M 9786, which offers superior wrinkle resistance, durability, and adhesion.

● Includes double-sided tape.

[Disclaimer]
Due to the nature of the product material and color, certain colors (green, orange, red, pink, yellow)
may fade over time or with use.
Please note that claims regarding fading or discoloration will not be accepted.

[Regarding products marked as "取り寄せ" (backorder) or "予約" (pre-order)]
These products will be custom-made by the manufacturer.
Please note that due to custom production, changes or cancellations cannot be accepted after ordering.
Please be aware that it takes approximately 2 to 2.5 months for backordered items to be delivered.

[Compatible models] YAMAHA Superjet (2021)

Made of aluminum billet

New wing design dramatically increases hookups.
Improves top speed, turning and handling in rough water.
Perfect for racing purposes as well as free riding.
Significantly reduces cavitation.

The water intake port at the back of the gate (UNLIMITED logo) is designed to be raised higher than usual (4mm higher) to allow more water to be sent to the pump.

[Compatible models] SEADOO
GTX-LTD / GTX (2018-)

The birth of an ideal seat cover that combines both "race" and "recreational" aspects!
The main material is a combination vinyl made of "Ballistic Nylon" and "Ultra Grade".
A non-slip top for perfect riding and UNLIMITED stitching that stands out against the black color enhances the sense of luxury!
Based on these limited materials,
This is a collaborative seat cover carefully handmade by JETTRIM, a popular American brand that is home to jet sports.

This is a custom specification that aims for the highest quality.

[Compatible models] SEA-DOO iTC/iBR equipped model
Lever billet case for electronic throttle (iTC) and I-brake (iBR) systems

[UL36006] SEA-DOO mode select system case

The handlebar can be replaced by relocating and attaching the mode select button.
A sophisticated and stylish design made from machined aluminum that eliminates waste.

UNLIMITED iTC/iBR billet switch case kit (product number: UL36000)
★The billet lever case in the above kit can be purchased separately.

[Compatible models] SEA-DOO iBR equipped model
Lever billet case for I-brake (iBR) system

[UL36003] Left side: I brake (iBR) lever case

Move the iBR sensor to the housing case,
Handlebars can be replaced by attaching a lever.
A sophisticated and stylish design made from machined aluminum that eliminates waste.

UNLIMITED iTC/iBR billet switch case kit (product number: UL36000)
★The billet lever case in the above kit can be purchased separately.

[Compatible models] SEA-DOO iTC equipped model Lever billet case for electronic throttle (iTC) system

[UL36004] Right side: Electronic throttle (iTC) lever case

Move the iTC and iBR sensors to the housing case,
Handlebars can be replaced by attaching a lever.
A sophisticated and stylish design made from machined aluminum that eliminates waste.

UNLIMITED iTC/iBR billet switch case kit (product number: UL36000)
★The billet lever case in the above kit can be purchased separately.

SEA-DOO
Models equipped with electronic throttle (iTC) and I-brake (IBR) systems from 2009 onwards

[There may be additional parts required depending on the compatibility details and model. Please check the product description]

[Compatibility details]
2011~ T3 Hull (RXP-X 260 IS･AS), 2016~ T3 Hull (RXP-X 300 IS･AS)
2011~ S3 Hull (RXT・RXT-X・GTX/IS・AS), 2009 S3 Hull (IS・AS Series)
2011~ GTI series (GTI130 / SE155 / WAKE155 / GTR)
2014~ SPARK

[About required parts]
*S3 Hull...The angle adjustment range of the normal steering wheel tilt function is limited.
*T3 Hull, RXP-X260/300, 2015 and later models...Top plate [UL35100TP-2] sold separately is required.
*SPARK…Removal of stainless steel DESS post holder plate requires SPARK dedicated top plate [UL35100TP-SP] sold separately.

New design and low price!
10cm lower than the normal position, allowing riding in a low position.
An offset handlebar clamp [UL062] is installed.
Other handlebar clamps from the same company can be attached.
*Depending on the model, the hull and handle may interfere.

【Guidance】
●Recommended for use with the company's billet switch case set [UL36000] and ITC/IBR billet lever [UL33002] ●It is also possible to process and use the X series genuine switch case.
●The handlebar of the SEA-DOO model is now replaceable.

[Applicable models] SEA-DOO iTC/iBR (*) Equipped models *For electronic throttle (iTC) and I-brake (iBR) systems after 2009 (*excluding 2018 model)

Aluminum billet housing case for the levers and switch buttons of the above models.A sophisticated and stylish design made from machined aluminum that eliminates waste.
The iTC and iBR sensors are relocated to the housing case and the handlebar can be replaced by attaching a lever.

[Kit contents] Total 6 parts [1] Throttle lever housing,
[2] Reverse lever housing,
[3] MODE/SET button housing,
[4] Suspension/Cruise button housing,
[5] START/STOP switch housing,
[6] Cruise switch housing

[Disclaimer] *Only the above kit contents are included; the products used in the installation image are not included.

[Compatible models] KAWASAKI Kawasaki
ULTRA300X / ULTRA300LX / ULTRA300SE
ULTRA310LX (-'21) / ULTRA310X / ULTRA310SE

Used to relocate the cruise control button when replacing the accelerator lever.
Available in 4 colors, you can color coordinate the throttle lever and hull.

When replacing the throttle lever
●When trying to use the cruise control function at the same time...
You must replace the stock steering mount with an aftermarket steering mount and use a relocation plate.

●By using this case together
[Using the cruise control function with the original steering mount] Furthermore
[Replacing the throttle lever without losing the position tilt function] is now possible.

[Applicable models] SEA-DOO iTC/iBR equipped model Lever billet case for electronic throttle (iTC) and I brake (iBR) system

[UL36005] Case for SEA-DOO mode select system

Left side: Sports mode/Eco mode VTS button case

The handlebar can be replaced by relocating and attaching the mode select button.
A sophisticated and stylish design made from machined aluminum that eliminates waste.

UNLIMITED iTC/iBR billet switch case kit (product number: UL36000)
★The billet lever case in the above kit can be purchased separately.

[Compatible models] KAWASAKI ULTRA series / YAMAHA GP1800
■Handlebar clamp: Compatible with standard handlebar diameter 22.2mm

●KAWASAKI ULTRA310X /310R /310LX (-'21) /310X SE /300X /300LX /260X /260LX /250X /LX
●YAMAHA GP1800 / VX series ('15-)

■Material: Made of billet aluminum

This adapter allows you to replace the handlebar while using the genuine handlebar mount.
To replace the handlebar of a model that uses a V-shaped handlebar mount,
It used to be necessary to replace the steering mount, but with this product, you can now replace the handlebar!

For the ULTRA series, we use the genuine OEM mount as is, so
The steering wheel tilt function can also be used as is.

[Compatible] Can be installed on runabout models

[Included] UL31100 bar pad included (pad length 230mm) *Color cannot be specified

【specification】
■Material: Aluminum ■Type: φ7/8" (22.4mm) standard ■Total length: 850mm
■Handlebar clamp area: 130mm
■Grip end position: 65mm

Minimize clamping area, grip, switch case,
Handlebar with maximum throttle lever aria.
Bending tie compatible with recent models.
The shape that hangs toward the bar end creates a riding form that naturally closes the sides when cornering.

[Applicable models] All KAWASAKI 4-stroke models

Performance dress-up parts with high quality strength and precision!
Weight reduction has also been achieved by simplifying the air suction valve.

*In order to install this part to Kawasaki's SC model, it is necessary to remove and install the head pipe.

[Compatible models] KAWASAKI Kawasaki
650/750/800/900/1100 engine

The inside of the engine room stands out.
*Please use the genuine O-ring when installing.

UL044SL Silver
UL044BK Black
UL044GR Green
UL044RD Red
UL044BL Blue

[Application]
Used in KAWASAKI electrical box
Replacement parts for plastic joints.

■Quantity: 1 piece
■Billet specifications

There is no need to worry about damage due to deterioration due to years of use, and the visual appearance is also dressed up!

[Disclaimer]
*O-rings and grommets are not included with this product.

UL046SL Silver
UL046GM Gunmetal

[Compatible models] KAWASAKI
1500SX-R New SX-R
800SX-R
800X-2
STX900

Aluminum billet exhaust cover
Not only the 1500SX-R but also Kawasaki's stand-up 800 series can be installed.
Contrast cuts with a wide variety of colors,
This contributes to weight reduction while creating a luxurious rear view.

UL14020BK Black
UL14020SL Silver
UL14020GR Green
UL14020GM Gunmetal

[Applicable models] KAWASAKI 4-stroke

*When installing, please use the genuine O-ring (92055-1295).

Make your personal watercraft's genuine cam cover stylish! Dress up your engine room.

【Compatibility】Can be installed on runabout models. 【Type】Standard 22.4mm handlebar diameter 【Included】Comes with a handlebar pad (pad length: 220mm)

●The wide handlebars provide a natural and aggressive riding experience. ●Due to the wide handlebars, it is easy to adjust (cut) the handlebars to your desired length. ●The racing handlebar, made from aircraft-grade material, is coated with carbon fiber, creating a Spartan yet stylish look. ●The angle and length are based on conventional racing bars, but with scales printed to accurately set the mounting position, which is convenient for setup. ●This is the world's first innovative handlebar exclusively for watercraft, with absolutely no SWEEP (pullback). It is used and recommended by top riders worldwide. Its feature is that it eliminates interference between the handlebar and your side during low-center-of-gravity cornering, allowing you to maintain a more forward-leaning posture.

■Material: Aluminum
■Hose piercing port: Ф13mm
■Exit hole: Ф10.5mm
■Mounting hole: Ф16mm

UL008SL Silver
UL008BK Black
UL008GR Green
UL008BL Blue

【Compatible Models】
SEA-DOO WAKE (2011-2017)

※For WAKE Pro (2010-2017), use part number: 295100720
※For WAKE Pro (2018), use part number: 295100697

Genuine SEA-DOO PWC Cover.
Designed for a perfect fit and made with UV-resistant fabric.

【Important Information Regarding Genuine Products】
※This is an取り寄せ商品 (ordered-in-item)※
※As this is a genuine product, cancellations and returns after ordering are not accepted※

●When selecting a product, please ensure you check the following items before placing your order:
1. Please carefully confirm the manufacturer, 2. model name (common name), and 3. model year before purchasing.
●About the displayed price
Prices and specifications are subject to change without notice. Due to changes in manufacturer part numbers, prices, etc., the listed price may differ from the actual selling price. In such cases, we will contact you before shipping; thank you for your understanding.

【Please Read Before Ordering】
This product is a **manufacturer取り寄せ商品 (ordered-in-item) (genuine part)**.
As we promptly place orders with the manufacturer after your order is confirmed, cancellations and changes to order content due to customer convenience are generally not accepted.
Additionally, depending on the manufacturer's stock status, delivery may take some time. We will inform you of the delivery time as soon as it is confirmed.
Thank you for your understanding and cooperation when placing your order.