Collection: battery switch charger

[Compatible models]
KAWASAKI Jet Ski ALL Model
YAMAHA Marine Jet ALL model
SEADOO 4-stroke model (2018 or later) / SPARK(※)
*'18 -'20 RXP-X / '18-20: Not compatible with all GTI, GTR / '16-'17 SD models.
*Please use 30 for 4-stroke models up to 2015.

【compatibility】
■Yuasa:
YTX20, YTX20L, YTX20BS, YTX20HBS, YTX20LBS, YTX20HLBS, YTX20HLBSPW,
YTX20H, YTX20HL, YTX20HL-PW,
YB16A, YB16A2, YB16B, YB16B2, YB16HLACX, SYB16LB, YB16LA, YB16LA2,
YB16LB, YB16LB2, YB16CB, YB16CLB, YB16BCX,
GT16L-BS, GT16BS, CTX19-BS CTX19L-BS , GYZ20H, GYZ20L, GYZ20HL,YTX20L-BS,YB16CL-B
■DEKA: ETX16, ETX16L, ETX20, ETX20L
■ODYSSEY: PC535, PC625

【Product Specifications】
MBTX20U
■Size (mm): L:175 W:87 H:155
■Spacer (mm): Bottom: 20mm Side: 13mm
■Voltage (V): 12V
■Cold cranking ampere (CCA): 310 A
■Capacity (10HR) 21 Ah

●Patent: Quad flex terminal
Innovative terminal arrangement allows for flexibility in connecting aftermarket accessories.

●Innovative power balance
Batteries in the powersports market continue to face three problems.
1.Big vibration
2. High load at start-up
3.Load due to additional accessories
MOTOBATT's innovative power balance design overcomes these problems.
By reviewing the conventional cranking power (CCA) and emphasizing ampere hour (Ah),
Quick power recovery allows you to cope with repeated startups with extra power.

●AGM (absorbed glass mat) design
Classified as a dry type battery designed by AGM, it has a long life and there is no need to worry about leakage, so it can be used in harsh environments.
The plates inside the battery are encased in a glass mat soaked with electrolyte, so the contact surface is always maximized and protected from vibrations.
The self-discharge rate is much lower than that of the wet type, and deeper discharge is also possible.
Even if the battery runs out, charging will restore it without reducing performance.
80% of initial battery failures are due to incorrect injection of electrolyte.
MOTOBATT is optimally adjusted at the factory and can be installed right out of the box.

【Guidance】
Some MOTOBATT products include
A "spacer" is included, so please use it as necessary.

[Compatible models]
SEA-DOO 4-stroke (up to '15)
*Cannot be used with SPARK

■Since this is an instant-use battery, it can be used after injecting the electrolyte and leaving it for about 30 minutes.
■When using in low temperatures or if the product has not been used for a long period of time, please charge it for 1 to 2 hours before use.
*You can use it for a longer period of time by regularly maintaining it so that it does not drop below 12.3V.

■Calcium battery liquid refill type■Size: Width 170 x Length 130 x Height 195mm

■Voltage: 12V ■10-hour capacity: 30Ah ■Charging current: 3A
Weight: 9.31KG

■ Country of Origin: China

[Features]
Excellent self-discharge performance, long life, and starting performance
By making the electrolyte into a gel, we were able to improve the basic performance that is important for a battery.
.
●It will not leak even if it falls on its side! It is a gel battery with a cutoff function, so it will not leak even if it falls on its side .
No need to worry about leaks, etc. ●Maintenance-free
merchandise
Since the battery is shut off from the time of purchase, there is no need to inject/replenish battery fluid, so it is hassle-free.
Pay attention to the charging current.

*Initial charging time: 1 to 2 hours
*If the engine is difficult to start during cold winter temperatures or after the battery has been manufactured, charging will be necessary.

●YAMAHA Genuine Parts

●Waterproof Battery Switch Set for MJ FX, VX, EX Series

●Set Contents: Battery switch body, power cable, screws, and other necessary mounting parts

【Specifications】
Rated voltage: DC12V Rated current: Max 60A

●This is a waterproof battery switch set that allows you to easily turn the marine jet's battery power on/off.

●It saves you the trouble of disconnecting the cable from the battery terminal when the marine jet is not in use.

●It includes all the necessary materials for installation, such as the switch, power cable, and screws.

【Please check before ordering】
This product is a **manufacturer-ordered product (genuine parts)**.
Once an order is confirmed, we will promptly place an order with the manufacturer. Therefore, cancellations or changes to order contents due to customer convenience are generally not accepted.
Also, delivery may take time depending on the manufacturer's stock status. We will notify you of the delivery time as soon as it is confirmed.
Please place your order after acknowledging this in advance.

[Compatible models]
SEA-DOO 4-stroke (~'15)
*Not compatible with SPARK

■This is a ready-to-use battery. After injecting the electrolyte, it can be used after resting for about 30 minutes.
■For low temperatures or items that have not been used for a long time, please use after charging for 1-2 hours.
*You can use it for as long as possible by always maintaining it so that it does not fall below 12.3V.

■Calcium battery fluid refill type
■Size: W170 x H130 x D195mm

■Voltage: 12V ■10-hour rate capacity: 30Ah ■Charging current: 3A
■Weight: 9.31KG

■Country of origin: China

[Features]
●Excellent self-discharge performance, long life, and starting performance
By gelling the electrolyte, we were able to improve the basic performance important for batteries.
.
●No liquid leakage even if it falls over! It's a sealed gel battery, so even if it falls over,
there's no need to worry about liquid leakage. ●Maintenance-free
Since the product is sealed from the time of purchase, there's no need to inject/refill battery fluid, saving you time. However,
be careful with the charging current.

*Initial charging time: 1-2 hours
*Charging may be necessary for low temperatures in winter, or if the engine has difficulty starting after a period of non-use since manufacturing.

[Disclaimer]
*Cannot be shipped to Okinawa Prefecture and isolated islands in each prefecture.
*Due to the nature of the product, some items cannot be shipped together.

[Compatible models]
SEA-DOO 4-stroke (up to '15)
*Cannot be used with SPARK

■Since this is an instant-use battery, it can be used after injecting the electrolyte and leaving it for about 30 minutes.
■When using in low temperatures or if the product has not been used for a long period of time, please charge it for 1 to 2 hours before use.
*You can use it for a longer period of time by regularly maintaining it so that it does not drop below 12.3V.

■Calcium battery liquid refill type■Size: Width 170 x Length 130 x Height 195mm

■Voltage: 12V ■10-hour capacity: 30Ah ■Charging current: 3A
Weight: 9.31KG

■ Country of Origin: China

[Features]
Excellent self-discharge performance, long life, and starting performance
By making the electrolyte into a gel, we were able to improve the basic performance that is important for a battery.
.
●It will not leak even if it falls on its side! It is a gel battery with a cutoff function, so it will not leak even if it falls on its side .
No need to worry about leaks, etc. ●Maintenance-free
merchandise
Since the battery is shut off from the time of purchase, there is no need to inject/replenish battery fluid, so it is hassle-free.
Pay attention to the charging current.

*Initial charging time: 1 to 2 hours
*If the engine is difficult to start during cold winter temperatures or after the battery has been manufactured, charging will be necessary.

[Compatible models]
KAWASAKI KAWASAKI *Excluding 550/650(-96) and 800X-2

SEA-DOO 4 stroke (16-) SPARK Spark

■Since it is a ready-to-use battery, it can be used for about 30 minutes after injecting electrolyte.
■If the product is at low temperatures or has not been used for a long period of time, please charge it for 1 to 2 hours before using it.
*You can use it for a long time by constantly maintaining it so that it does not fall below 12.3V.
*For model compatibility, please refer to [Click here for compatibility table] below the image.

●Maintenance-free battery, no need to replenish fluid.
●Calcium battery ■Size: Width 175 x Height 88 x Height 155mm

Used for joints of independent wiring in campers, trailers, etc.
The main body can be fixed, and can be easily attached and detached with one touch.

●Cable used
Core diameter: ~5mm (17sq)
Allowable current: 50A

[Product specifications]
■Maximum capacity: 300Amp
■Flange diameter: 58.5mm
■With waterproof cap
*Detailed size is shown in the photo

●A simple toggle switch type battery switch.
●Can be used to supply and cut off battery power.
●The red switch lever can be removed.

[Product specifications]
■Set of 1 each of plus (red) and minus (blue)
■Can be used up to 800 amperes.

[Applicable] The tip of the terminal (the thinnest part of the terminal)
Suitable for φ17.4mm positive type and φ15.8mm negative type.
■Can also be installed on types with bolts attached to the battery terminal.
■For D terminal
*Not available for positive type φ12.7mm and negative type φ11.1mm

A connector that can be connected to and removed from the battery terminal with a single touch.
Lift up the blue or red cap to loosen the terminal.
You can easily remove the wires from the battery. Attaching is the reverse operation.

[Product specifications]
■Size: Length 860 x Width 270mm
■Dial diameter: 350mm
■Terminal installation inner diameter: 19mm

■Applicable: For small batteries
■Can be used up to 800 amperes.

This is an ON/OFF switch attached to the battery terminal (negative side).
You can turn the power on/off by tightening or loosening the green knob that comes with the terminal.

This is a switch that turns ON/OFF (1 system) power supply from the battery.
Manufactured by BLUE SEA, which boasts a top market share in the United States for RV and boat-related electrical wiring parts and is recommended by many builders.
The MINI Battery Switch is ideal for outboard boats and boats with small diesel engines.

[Product specifications]
■Continuous withstand current: 300Amp
■Momentary withstand current: 1500Amp (2.5 seconds)
■Maximum voltage: 48V
■Size: 68.9x68.9mm
■Terminal stud: 9.5mm

■Installation method: Compatible with mounting methods such as embedded in the wall or stationary.
■Six types of stickers (``ENGINE'', ``ENGINE1'', ``ENGINE2'', ``GENERATOR'', ``HOUSE'', and ``INVERTER'') can be attached to the knob section depending on the purpose.

■■■■■Main features■■■■■
●The connection terminal uses highly conductive copper and is coated with corrosion-resistant tin plating. Achieved reliable wiring.
●The ring sticker and knob that indicate the switch position use luminescent labels. You can operate it without any mistakes even in dark places.
●You can tell that the knob is firmly in each position by a firm "click" response.

This is a switch that turns ON/OFF (1 system) power supply from the battery.
Manufactured by BLUE SEA, which boasts a top market share in the United States for RV and boat-related electrical wiring parts and is recommended by many builders.
The MINI Battery Switch is ideal for outboard boats and boats with small diesel engines.

[Product specifications]
■Continuous withstand current: 300Amp
■Momentary withstand current: 1500Amp (2.5 seconds)
■Maximum voltage: 48V
■Size: 68.9x68.9mm
■Terminal stud: 9.5mm

■Installation method: Compatible with mounting methods such as embedded in the wall or stationary.
■Uses a removable key type that is effective in preventing tampering. Prevents mischief and malfunction.

■■■■■Main features■■■■■
●The connection terminal uses highly conductive copper and is coated with corrosion-resistant tin plating to ensure reliable wiring!
●The ring sticker that indicates the switch position uses a luminescent label. You can operate it without any mistakes even in dark places.
●You can tell that the knob is firmly in each position by a firm "click" response.

■The MINI battery switch is ideal for outboard boats and boats equipped with small diesel engines.
■Battery switch that supplies two systems from two batteries. [Switch position] The following four positions are available.
1. Battery 1 → Connect/cut off the power to the two devices.
2. Battery 2 → Connect/cut off the power to the two devices.
3. Battery 1 + 2 → Connect/cut off the power to the two devices.
4. Shut off all batteries 1+2.

[Product use]
●Continuous withstand current: 300Amp
●Momentary withstand current: 1500Amp (2.5 seconds)
●Maximum voltage: 48V
●Size: 68.9x68.9mm
●Terminal stud: 9.5mm

■Installation method: Compatible with mounting methods such as embedded in the wall or stationary.
■Six types of stickers (``ENGINE'', ``ENGINE1'', ``ENGINE2'', ``GENERATOR'', ``HOUSE'', and ``INVERTER'') can be attached to the knob section depending on the purpose.

■■■■■Main features■■■■■
●Highly conductive copper is used for the connection terminal, and the corrosion-resistant tin plating coating ensures reliable wiring!
●The ring sticker and knob that indicate the switch position use luminescent labels. You can operate it without any mistakes even in dark places.
●You can tell that the knob is firmly in each position by a firm "click" response.

●A battery switch that supplies two systems from two batteries; the switch position is from battery 1 to connect/cut off power to two devices. Battery 2 → Connect/cut off power to two devices. Battery 1+2 → Connect/cut off power to two devices. All batteries 1+2 are cut off. It has 4 ways.

●The e-series is ideal for boats equipped with small to medium-sized diesel engines.

●Manufactured by BLUE SEA, which boasts a top market share in the United States for electrical wiring parts related to RVs and boats, and is recommended by many builders.

●Continuous withstand current: 350Amp

●Momentary withstand current: 1750Amp (2.5 seconds)

●Maximum voltage: 48V

●Size: 97.8×97.8mm

●Terminal stud: 9.5mm

◆◆◆Main features◆◆◆

●The connection terminal uses highly conductive copper and is coated with corrosion-resistant tin plating. Achieved reliable wiring.

●The ring sticker and knob that indicate the switch position use luminescent labels. You can operate it without any mistakes even in dark places.

●You can tell that the knob is firmly in each position by a firm "click" response.

●There are two installation methods. Compatible with wall mounting and stationary mounting methods.