Collection: All items

19-1600: SBN38mm
19-1601: SBN44mm

A set of replacement butterfly and shaft.

[Applicable] Mikuni carburetor YAMAHA GP1200R/XLT1200/XL-L

You can easily adjust the screw by replacing it.
Easily change carburetor settings.

When used by attaching it to a stabilizer, it improves straight-line performance,
Make control safer and easier.

■Quantity: 1 set of 2 pieces of the same color
■Compatible with: Hydrofoil stabilizer exclusive product
→Large type: Compatible with product number 04824 / 21971
→Small type: Compatible with product number 04826 / 21972

[Effect]
●The water flow flowing on the surface dynamically creates upward thrust pressure on the bottom surface of the stabilizer, pushing up the stern and pushing down the bow, shortening the time until planing, increasing propeller efficiency, and improving fuel efficiency!
●The water flow created by the propeller is efficiently pushed backwards, improving controllability and straightness.

●The time until planing is halved, making running and control smoother. It also saves fuel consumption by 10-40%.

[Installation method]
1■ Place the stabilizer on the cavitation plate and mark the 4 places to drill holes.
*At that time, after drilling a hole with a diameter of 6 mm, make sure that there is a gap of at least 1 cm between the edge of the cavitation plate and the edges of all four holes.
*If there is no gap of 1cm or more, the cavitation plate cannot be installed as there is a possibility that it will be damaged while driving.

2■ Use a drill to drill holes with a diameter of 6 mm in four locations, and then pass the included bolts from under the cavitation plate.
*From the bottom, temporarily tighten the 4 places by inserting the bolts → cavitation plate → rubber washer → stabilizer → washer → nut.

3■ Perform the final tightening, but instead of final tightening one location at a time, do it diagonally a little at a time, ``evenly in four locations in an X-shaped order.''
4■ Since a locking nut is used, there is no need to tighten the bolts until the stabilizer is deformed.
5■ Move the stabilizer and check that if there is no play, the installation is complete.

【lastly】
Do a test drive and check again to make sure there is no play between the stabilizer and cavitation plate.

[Product specifications]
■Type: Large
■Color: Black / Gray
■Size: Please check the image.
■Correspondence
→Large: 40 to 300 horsepower outboard motor, inboard/outboard motor

A spare/replacement bulb for navigation lights manufactured by Koito Seisakusho Co., Ltd.
JCI certified product Type approval number obtained

■Applications: 4 types of front lights, 2 types of rear lights, 2 types of bicolor lights, 2 types of white lights
01458: 12V10W
01459: 24V10W

[Note] Please select the voltage and wattage before ordering.
●Voltage: 12V/24V
● Wattage: 10W/20W/30W
We have the above lineup. (This product is 10W)
Please select the appropriate product according to your application.

Manufactured by Koito Seisakusho Co., Ltd.

A spare/replacement bulb for navigation lights manufactured by Koito Seisakusho Co., Ltd.
JCI certified product Type approval number obtained

■Application: 01457 → front light three types of light, 01468 & 01469 → red light
01457: 24V20W
01468: 12V30W
01469: 24V30W

[Note] Please select the voltage and wattage before ordering.
●Voltage: 12V/24V
● Wattage: 10W/20W/30W
We have the above lineup. (This product is 20W & 30W)
Please select the appropriate product according to your application.

Manufactured by Koito Seisakusho Co., Ltd.

A spare/replacement bulb for navigation lights manufactured by Koito Seisakusho Co., Ltd.
JCI certified product Type approval number obtained

■Application: Application: Gendou, tricolor light
01456: 12V20W
26705: 24V20W

[Note] Please select the voltage and wattage before ordering.
●Voltage: 12V/24V
● Wattage: 10W/20W/30W
We have the above lineup. (This product is 20W)
Please select the appropriate product according to your application.

Manufactured by Koito Seisakusho Co., Ltd.

[Product specifications]
■Type: Recessed type
■Material: Stainless steel
■Total length: 220mm
■Holder inner diameter: 41mm
[Contents] 5-piece set: rod holder, rubber, stop bolt, intermediate pedestal, and pedestal.
...
■With base gasket integrated rubber cap

This is a stainless steel rod holder made by Atwood.
Comes with a UV-resistant cap to prevent water from entering.

Made by ATTWOOD

[Product specifications]
■Material:
■Size: Diameter/Length/Eye diameter
G-1: 89mm /330mm / 9mm
G-2: 114mm /406mm / 12mm
G-3: 140mm /508mm / 12mm
G-4: 165mm /584mm /19mm
G-5: 216mm /678mm /19mm
G-6: 257mm /762mm /22mm

●Highly weather resistant standard model that protects your boat from scratches ●Polyform's air fender, G series fender.
●Standard bale-shaped design that perfectly matches any ship.

【please note】
*Since it is a sealed type, it will be delivered with air injected.
*Please note that additional air injection is not possible.
POLYFORM Manufactured by POLYFORM

[Product specifications]
■Material: Made of reinforced vinyl
■Diameter: Approximately 20cm

●Multi-use float that can be used as a marker buoy or fender.
●This buoy is ideal for setting up courses for water skiing, wakeboarding, personal watercraft, etc.
●Made of marine grade reinforced vinyl, the same as commonly used air fenders,
It is less susceptible to deterioration due to UV rays.

●Three fluorescent colors that are highly visible even on water.
●It is a product that does not easily fade even after long-term use.

【please note】
Air injection nozzle is not included.
*Please purchase the air injection nozzle (product number: 97560) separately.

【Product Specifications】
■New Standard Compliant Model/TYPE: A
■Applicable Weight: 40kg or more. Can be used for children.
■Initial Buoyancy: 7.5kg
■Waist Size: Up to 105cm
■Material: (Body) Polyester, (Buoyancy Material) Oil-resistant foamed polyethylene

This is a fixed-type life vest that boasts absolute safety.
Because it is worn like a vest, it is less likely to come off in the event of falling into the water.
The front closure is zippered.

By replacing the hose,
This is an air pump with excellent cost performance that can be used for both intake and exhaust.
■3 types of adapters are standard equipment

When using on towing tubes, please use a foot pump or hand pump for finishing.

1. 24758: DC12V (Cigarette lighter plug)
■Voltage/Current DC12V/12A
■Air flow rate 280 liters/min
■Maximum pressure 0.05kg/cm2
■Continuous use time approximately 12 minutes

2. 24759: AC100V (outlet plug)
■Voltage/Current AC100V/1.8A
■Air flow rate 300 liters/min
■Maximum pressure 0.06kg/cm2-
■Continuous use time approximately 12 minutes

●10 pieces

●Hose outer diameter:

16mm…for 5/16

18mm…for 3/8

24mm…For primer pump

[Product specifications]
■Size: Diameter / Total length / Hole diameter
HTM-1: 152mm /381mm /16mm
HTM-2: 203mm /508mm /16mm
HTM-3: 254mm /660mm /16mm

●Polyform's air fender, HTM fender.
●Type with a through hole in the center for the rope to pass through. You can hang the fender with a single rope, which is very convenient when installing it horizontally.
●You can also hang it vertically by making a knot after passing the rope through it.

【please note】
Nozzle is not included.
*Please purchase the nozzle (product number: 97561) sold separately.

POLYFORM Manufactured by Polyform

A jacket with a simple and universal design that uses a polyester body liner as the outer material.
The body also has a texture similar to a thin down jacket.

This item shows JETPILOT's attention to detail in detail, such as the left and right front welt pockets with zips and the contrasting design of the hoodie straps.

Although it is simple, it is a useful item as the main outerwear for styling.

■Actual size when laid flat (chest measurement/length)

M size: 120cm/62cm
L size: 125cm/64cm
XL size: 129cm: 67cm

*Please forgive any errors as the measurements are taken by our staff.

This is Annieversary model apparel with the original logo revived.
The brushed lining makes it a little looser, and the fabric isn't too thick, so it's perfect from fall to spring!
Round neck trainers with a simple design are popular among people of all ages.

■Poly/cotton outer body 320gsm fleece brushed lining type

■Actual product size (chest measurement/length)

S: 95cm/70cm
M:100cm/72cm
L:106cm/74cm
XL:116cm/77cm

*Please note that there may be errors due to measurements taken by our staff when placed horizontally.

*American size, one size larger than Japanese size.

[As this is a special price item, we cannot accept returns or exchanges. ]

This is a support collaboration model with the Kawasaki logo.
The lining is satin quilted, giving it a heavy texture similar to that of a jacket.

■Material: Cotton

■Actual product chest measurement S: 100cm
M: 110cm
L: 120cm
*Please allow slight errors due to the actual size measured by our staff when placed horizontally.

[As this is a special price item, we cannot accept returns or exchanges. ]

These board shorts have a cool gradation line.
Due to the central waist strap design, only minor adjustments are required.
There is a zip pocket on the side

■Material: Stretch polyester

■Waist size
30 inches (80cm)
32 inches (85cm)
34 inches (90cm)
36 inches (95cm)
38 inches (100cm)

Board shorts surf pants saltwater pants beach swimming pool resort
Watercraft Wakeboard Surfing Flyboard
Kitesurfing Famous Brand Popular JET-PILOT America
Outdoor Marine Activities SURF WAKEBOARD SUP Paddle Board
Kayaking Canoeing Trekking River play Jet skiing

■Material: 92% Polyester, 8% Spandex
■Specifications: 1 right leg pocket

■Jetpilot Recommended Waist Sizes
　28 inches (74-78cm)
　30 inches (78-82cm)
　32 inches (82-86cm)
　34 inches (84-88cm)
　36 inches (86-90cm)
　38 inches (88-92cm)
*Please note that the suitable size may vary depending on the waist design.

■Actual Garment Measurements (Laid Flat)
28 inches: Waist 76cm, Total Length 49cm, Inseam 24cm
30 inches: Waist 80cm, Total Length 50cm, Inseam 25cm
32 inches: Waist 84cm, Total Length 51cm, Inseam 25cm
34 inches: Waist 90cm, Total Length 52cm, Inseam 25cm
36 inches: Waist 94cm, Total Length 54cm, Inseam 26cm
38 inches: Waist 100cm, Total Length 55cm, Inseam 26cm
*Please allow for slight measurement error by our staff.

Boardshorts, Surf Pants, Swim Trunks, Pool, Resort
Personal Watercraft, Wakeboard, Surfing, Flyboard
Kitesurfing, Famous Brand, Popular, JET-PILOT, USA
Outdoor, Marine Activities, SURF, WAKEBOARD, SUP
Paddleboard, Kayak, Canoe, Trekking, River Play
Jetski, Fishing, Boat

One Size Fits All

This hat is water-repellent, durable, and resistant to friction, making it suitable for both city and outdoor use. It can be folded and stored in a bag, making it very convenient to carry and store. When unfolded, it immediately returns to its original shape and can be used. It's also perfect for sun protection. This versatile hat can be used for both casual outings and outdoor adventures.

・Quick-dry fabric
・Lightweight and breathable
・Adjustable and removable chin strap
・Hidden inner pocket

Logo print wide brim outdoor marine sports water sports sun protection lightweight quick dry fishing black JPW74 74 JETLITE WIDE BRIM HAT

The brand's top-grade materials provide comfortable PWC riding.
Featuring highly stretchable 2mm Flexlite neoprene, knee pads coated with 3D embossed rubber to enhance grip and prevent abrasion, and an embossed neoprene panel behind the knees to ensure stress-free movement even when bent, these specs are fully equipped with features for riding wear.
Recommended for those seeking the highest level of fit, functionality, and visual appeal.

【Long John】
 Removable back protection (spine protection) and shock-absorbing Pro-Tech Impact Protection System adopted on the back (see image)

●Durable YKK ankle & back zips for easy on/off
●Ankle - Velcro panel to cover the zipper
●Jet-Lock Seam Construction for enhanced strength
●Durable EVA Pro-Tech pads on knees and shins to reduce impact
●Seamless joint panels to reduce stress
●Lycra panels under arms to prevent chafing
●Airflow panels for breathability and comfort
●Oilslick logo

Top JA22156 (sold separately) Can be set up with the JACKET

■Applicable size guide (height, weight, chest, waist)
M ：170-175cm・65-72kg・ 95-100cm・76-81cm
L   ：175-180cm・70-77kg・100-105cm・81-86cm
XL ：180-185cm・77-85kg・105-110cm・84-88cm

360° stretch neoprene JETLITE foam is the lightest and most flexible foam. It has more air bubbles than conventional products, making it more flexible and movable, and is also lighter.

YKK lock zipper adopted

*This is a sports vest that can be used for wakeboarding, SUP, etc.
*JCI small special vessel inspection certification is not possible.

■Applicable waist circumference M:85-95cm
L:90-100cm
XL:95-105cm

Wakeboarding Wakesurfing Kiteboarding Surfing Bodyboarding
SUP SUP Paddleboard Flyboard Snorkeling Trekking
Kayak Canoe Marine Sports Marine Activities Banana Boat
Windsurfing WAKEBOARD SURF WATERTOY Rubber boat ZUPBOARD
Sports vest Impact vest Neo vest Wet suit

This is ZAHRA KELL's signature model.
Stretch neoprene accommodates every movement of the rider.
This neoprene vest is flexible and soft to the touch, making it the perfect piece for active scenes.
The liner is made of fire fur material, which is perfect for women as it provides excellent heat retention.
The front zipper makes it easy to put on and take off.
This is a top-quality vest that is lightweight and flexible.

■ Chest size guide

M(10):85-90cm
L(12):90-95cm

*JCI small special vessel inspection certification not available*

Wakeboarding, Wakesurfing, Kiteboarding, Surfing
Bodyboarding, SUP, Paddleboarding, Flyboarding, Snorkeling, Trekking, Kayaking, Canoeing, Marine Sports, Marine Activities, Banana Boat, Windsurfing, WAKEBOARD SURF WATERTOY
Rubber boat ZUPBOARD sports vest Impact vest Neo vest
Wetsuits

A light glove that eliminates hard padding and emphasizes comfort, making it suitable for high summer weather.

■Applicable size (hand width/total length/middle finger length)
(S)21.0cm/21.0cm/8.5cm
(M)21.5cm/21.5cm/8.5cm
(L) 22.0cm/22.0cm/9.0cm
(XL)23.0cm/23.0cm/9.0cm

*Please note that our measurements are taken horizontally, so please allow slight errors.
(US standard size)

Personal Watercraft (PWC) Watercraft Watercraft Jet Ski Watercraft Kawasaki YAMAHA SEADOO JET

Half-Finger Gloves

These gloves feature PVC molded protectors on the top of the fingers and back of the hand to reduce impact, and Lycra fabric on the joints and sides of the fingers for smoother movement.
The palm is made entirely of Clarino (durable synthetic leather), with double-stitched Clarino reinforcement in areas that rub against the grip, making these gloves both functional and highly durable.

■ Size Chart (Hand Width / Total Length)
(M) 21.5cm / 21.5cm
(L) 22.0cm / 22.0cm
(XL) 23.0cm / 23.0cm

*Please note that these are our flat measurements, so a slight error may occur. (US Standard Sizes)

This is a multi-use waterproof backpack made by Dry Case in the United States.
3 Rolling system with extremely high performance, even in bad weather such as water spray, mud, sea breeze, rain and fog
It firmly protects the clothes and equipment you put inside.

In addition, we use environmentally friendly materials that are resistant to tears and sharpness.
Even if it gets dirty, you can easily remove it by wiping it with a wet cloth.

●Size: 69 x 40 x gusset 18cm (capacity 30L)

The size is large enough to hold bath towels, footwear, and other small items.

Stable shoulder straps and waist belt allow you to use both hands.
It also comes with a sturdy rubber strap, so you can hold it in your hand.
It also has plenty of storage specifications, including a zippered mesh pocket on the front and side pockets on the left and right.
It also provides full support for your back or lower back.

This cloth mask uses 100% cotton for the outer material and 100% quick-drying polyester fabric for the lining.
There is a pocket inside the main body that can be used to insert non-woven fabrics, gauze, etc.

●Masks do not completely prevent infection (virus invasion).
●Non-medical use, non-dust-proof/gas-proof use

【Product Specifications】
■Set of 2 ■Outer fabric: 100% cotton
■Lining fabric: 100% polyester
■Ear hook part: 100% cotton
■Size: L (Men's) W22cm x H15cm (mask part)
*This is the size listed in the catalog and may differ from the actual size.

The optimal cutting pattern, which thoroughly analyzes rider movements based on impressions from exclusive professional riders and has undergone repeated testing, is adopted. This is an ideal wetsuit that effectively uses highly elastic materials. You will surely experience UNLIMITED's highest quality and potential.
The side cutting makes the body shape look clean and has excellent design.

-UNLIMITED RUSH-
Aiming for higher performance, under the supervision of UNLIMITED's exclusive professional riders, the design is focused on specifications that maximize the "power," "speed," and "stability" of PWC. This is the ultimate wear that allows riders to embody smartness that is in line with the times.

【Features】
・Shoulder Velcro
Smooth donning and doffing possible with Velcro on the left shoulder of the long john
・Stabilize Pad
The pad on the knee part helps improve grip during riding
・2.5mm Flex Neoprene
The new material, further evolved from conventional fabrics, offers the highest level of feel and elasticity.
・Ink Pad
Flexible and lightweight, yet pursues improved grip
・Ankle Zipper
Zippered Velcro tape for easy donning and doffing protects the slider

Kawasaki 800SX-R normal (genuine) hood only

Decal kit for 800SX-R normal hood.

It uses 3M full color sheets and has beautiful graphics, as well as
Easy-to-install cut patterns make new visuals easy to install.
This film has a proven track record of maintaining its original beauty over a long period of time due to its highly durable surface treatment.

The colors are standard green and red. Please choose your favorite color.

[Disclaimer]
As this item is made to order, we cannot accept changes or cancellations after the order has been placed.

Boat equipped with Kawasaki New SX-R transform hood (UL46100)

Decal kit for boats equipped with New SX-R Transform Hood (UL46100).

It uses 3M full color sheets and has beautiful graphics, as well as
Easy-to-install cut patterns make new visuals easy to install. This film has a proven track record of maintaining its original beauty over a long period of time due to its highly durable surface treatment.

The colors are standard green and red. Please choose your favorite color.

[Disclaimer]
As this item is made to order, we cannot accept changes or cancellations after the order has been placed.

Transform hood custom boat [Product number: UL46100] Dedicated jet cover

*About TYPE-A (UL54001)…
Compatible only with the mount (UL35211) that comes with the transform hood.
(Due to the exclusive design, other types of mounts cannot be installed even with the company's mounts.)

Jointly designed by UNLIMITED x LABIOS!
High quality from domestic production, from fabric to sewing
To protect the body, the inner fabric uses long fiber non-woven fabric to protect the fibers.
[Material] Polyester material

[Special points]
1. Colored tape to make it easier to see the front when hanging the cover
2.The hood and handle part are made of double layered non-woven fabric to prevent chafing and strengthen the fabric.
3. Fasten the strap with one touch under the hull and securely secure it to the hull.
4. UNLIMITED brand mark made of silicone

[Disclaimer]
Colors of stitches, tape, etc. may vary depending on arrival time.

For ULNIMITED full billet sponsons (UL53200)

aluminum billet

Contents: 4 pieces

[Applicable models] SEA-DOO 4-stroke model (excluding SPARK)

Install it on top of the genuine oil cap.
The clutch function that prevents the oil cap from being over-tightened remains the same.
The aluminum billet cap stands out as an accent in the engine room.

[Information] We also recommend using the company's billet oil filter cap (UL53001).

[Compatible models]
KAWASAKI Kawasaki
YAMAHA
SEADOO
*Processing to the hull is required for all models of all manufacturers.
*For models with a vent function (fuel tank pressure punishment valve) on the fuel cap, a separate tank pressure release is required.

Durable billet aluminum finish.

By installing this fuel filler on SEADOO boats and YAMAHA boats,
UNLIMITED billet fuel cap [Product number: UL030, UL036] etc.
Fuel cap for KAWASAKI can now be used.

General purpose
*If used on a model with a vent function (fuel tank pressure relief valve) on the fuel cap, a separate pressure relief must be provided.

Set of machined aluminum fuel cap and filler.
It has a built-in fuel hose that prevents fuel from blowing back.
Double line hose structure.

[Support] M8 flat head screw

[Quantity] 1 piece
*Usually countersunk screws require counterbore processing on the mating material,
By using rosette washers, you can use countersunk screws without machining.

Be stylish with your favorite color! Also good as a design element!
You can also dress it up by replacing the bolts that secure the sponsons.

[Compatible models]
SEA-DOO 4-stroke ALL model (*excluding SPARK)

*Please use the genuine O-ring when using.

The oil cap can be removed without special tools when changing the oil.
It's very stylish and makes the engine room stand out.

UL53001SL Silver
UL53001OR Orange
UL53001RD Red
UL53001YL Yellow

【 SEADOO 】 SEADOO
RXT230 / GTX / GTX LTD / WAKE PRO 230 (2019-2025)

● Deck mats for SEADOO, newly released by UNLIMITED.

● In addition to excellent cushioning from a two-layer mat structure,
designed with the latest laser processing technology,
these durable mats eliminate surface tension for smooth deck drainage
and provide high grip even when wet.

● The double-sided tape used is not conventional 3M tape,
but PSA2, newly developed based on 3M 9786, which offers superior resistance to wrinkles, durability, and adhesion.

● Double-sided tape included

【Disclaimer】
Due to the nature of the product material and color, certain colors (green, orange, red, pink, yellow)
may fade over time or with use.
Please note that fading and discoloration are not covered by warranty.

【Regarding "Backorder/Pre-order" items】
These items will be produced upon order by the manufacturer.
Please note that changes or cancellations after ordering are not possible due to custom production.
Please allow approximately 2 to 2.5 months for backordered items.

【SEADOO】SEADOO
RXT230 / GTX / GTX LTD / WAKE PRO 230 (2019-2025)

●New deck mat for SEADOO from UNLIMITED.

●In addition to excellent cushioning from its two-layer mat structure,
it incorporates the latest laser processing in its design,
eliminating surface tension and facilitating smooth drainage from the deck,
while also providing a durable mat with high grip even when wet.

●The double-sided tape used is not the conventional 3M tape,
but a new PSA2 based on 3M 9786, which offers superior resistance to wrinkles, durability, and adhesiveness.

●Double-sided tape included

【Disclaimer】
Due to the nature of the product's material and color, certain colors (green, orange, red, pink, yellow)
may fade over time and with use.
Please note that fading or discoloration will not be covered by warranty claims.

【Regarding products marked as "取り寄せ" (backorder) or "予約" (pre-order)】
These items are custom-made by the manufacturer.
Please note that changes or cancellations cannot be accepted after ordering due to the custom production.
Please allow approximately 2 to 2.5 months for backordered items.

【 SEADOO 】 SEADOO
RXT230 / GTX / GTX LTD / WAKE PRO 230 (2019-2025)

● Deck mats for SEADOO, newly released from UNLIMITED.

● In addition to excellent cushioning from a two-layer mat structure,
the mats are designed using the latest laser processing technology,
which eliminates the surface tension of water to allow for smooth drainage from the deck,
and also provides a durable mat with high grip even when wet.

● The double-sided tape used is not the conventional 3M tape,
but a new PSA2 based on 3M 9786, which offers excellent wrinkle resistance, durability, and adhesiveness.

● Double-sided tape included

【Please Note】
Due to the nature of the product material and color, certain colors (green, orange, red, pink, yellow)
may fade over time and with use.
Please be aware that fading or discoloration will not be covered by warranty.

【Regarding "Backorder/Pre-order" Items】
These items will be made to order by the manufacturer.
Please note that changes or cancellations cannot be accepted after ordering due to the custom production.
Please allow approximately 2 to 2.5 months for backordered items.

【 SEADOO 】 RXT-X300 (2019-2025), RXT-X 325 (2024-2025)

●Deck mat for SEADOO RXT-X, newly released by UNLIMITED.

●In addition to excellent cushioning from its two-layer mat structure,
it incorporates the latest laser processing in its design,
eliminating water surface tension and ensuring smooth drainage from the deck.
This results in a durable mat with high grip even when wet.

●The double-sided tape used is not the conventional 3M tape,
but PSA2, newly developed based on 3M 9786, which offers superior wrinkle resistance, durability, and adhesiveness.

●Comes with double-sided tape

【Please note】
Due to the nature of the product material and color, certain colors (green, orange, red, pink, yellow)
may fade over time and with use.
Please be aware that fading or discoloration will not be covered by warranty.

【Regarding "made-to-order" / "pre-order" items】
These items are custom-made by the manufacturer.
Please note that changes or cancellations are not possible after ordering for custom-made products.
Please be aware that made-to-order items typically take 2 to 2.5 months to be delivered.

【 KAWASAKI 】
STX160

●Deck mats for the Kawasaki STX160, newly released by UNLIMITED.
●In addition to excellent cushioning from its two-layer mat structure,
the latest laser processing technology was incorporated in its design,
eliminating surface tension to allow for smooth drainage from the deck,
and creating a durable mat that maintains high grip even when wet.

●The double-sided tape used is not the conventional 3M tape,
but rather a new PSA2 based on 3M 9786, which offers superior wrinkle resistance, durability, and adhesion.

●Includes double-sided tape

【Disclaimer】
Due to the nature of the product's material and color, certain colors (green, orange, red, pink, yellow) may
fade over time and with use.
Please note that fading and discoloration are not covered by warranty.

【Regarding "Backorder/Pre-order" Items】
These items will be custom-produced by the manufacturer.
Please note that changes or cancellations are not possible after ordering for custom-produced items.
Please be aware that backorders typically take about 2 to 2.5 months to process.

KAWASAKI
STX-15F/12F・STX-R・1100STX(00-)/900STX(01-)

●Deck mats for Kawasaki STX-15F/12F・STX-R・1100STX(00-)/900STX(01-), newly released by UNLIMITED.

●In addition to excellent cushioning provided by a two-layer mat structure,
incorporating the latest laser processing in its design ensures that the mat not only eliminates water surface tension for smooth deck drainage
but also achieves a durable mat with high grip even when wet.

●The double-sided tape used is not the conventional 3M tape;
instead, it's a new PSA2 based on 3M 9786, which offers superior wrinkle resistance, durability, and adhesion.

●Comes with double-sided tape

[Please Note]
Due to the material and color properties of the product, certain colors (green, orange, red, pink, yellow)
may fade over time and with use.
Please be aware that fading and discoloration are not covered under warranty.

[Regarding Pre-order/Reserved Items]
These items are made to order by the manufacturer.
Please note that changes or cancellations are not possible after an order has been placed for custom-made products.
Please allow approximately 2 to 2.5 months for these items.

【 KAWASAKI 】
ULTRA310(-'21)/300/260/250/LX

●Deck mat for Kawasaki ULTRA310(-'21)/300/260/250/LX, newly released by UNLIMITED.

●In addition to excellent cushioning from a two-layer mat structure,
it's designed with the latest laser processing technology,
eliminating water surface tension for smooth deck drainage,
and providing a durable mat with high grip even when wet.

●The double-sided tape used is not the conventional 3M tape,
but a new PSA2 based on 3M 9786, which offers superior wrinkle resistance, durability, and adhesion.

●Comes with double-sided tape

【Disclaimer】
Due to the nature of the product's material and color, certain colors (green, orange, red, pink, yellow)
may fade over time and with use.
Please note that fading and discoloration are not covered by warranty.

【Regarding "取り寄せ/予約表示の商品" (Items marked as "Order/Reservation")】
These items will be specially produced by the manufacturer upon order.
As these are custom orders, please note that changes or cancellations after ordering cannot be accepted.
Please allow approximately 2 to 2.5 months for these items to be prepared.